HAN-HBE15
$12.15 NZD
All prices include GST
Big Water Tanks is an official stockist of Hansen Products — New Zealand-made Easy Fit poly fittings for farm, irrigation, rural water and garden pipe. The Hansen Bracket Elbow (HBE) and Reducing Bracket Elbow connect a tap to low density poly pipe (LDPE) or EnduroFlex. One end is a BSPT thread outlet for the tap, with no nut; the other end is an Easy Fit poly end with a barbed tail and Poly Nut. Sizes are 15mm (1/2") and 20mm (3/4").
A bracket elbow is the Hansen fitting for putting a tap on the end of a poly pipe line. Hansen's catalogue describes it as "used for connecting taps to Low Density Polyethylene Pipe (LDPE) and EnduroFlex. Can also be used to connect taps to flexible pipe and hose. BSPT Thread Size x Pipe Size." It has two different ends. The thread outlet is a BSPT (tapered) thread for the tap and has no nut. Hansen doesn't say whether it is male or female. The poly end is a one piece Easy Fit end with no O-ring, no crimping and no solvent cement: push the pipe onto the barbed tail and wind on the Poly Nut, and the barbs grip the inside of the pipe while the nut grips the outside. Hansen moulds its Easy Fit fittings in New Zealand from UV stabilised glass fibre reinforced nylon, and the Easy Fit Poly range is tested to AS/NZS 4020:2018 for contact with drinking water.
The thread outlet is the BSPT (tapered) thread for the tap, with no nut. The poly end takes the pipe with a barbed tail and Poly Nut. Hansen lists the sizes as "BSPT Thread Size x Pipe Size".
15mm = 1/2" and 20mm = 3/4".
On the HBE15 and HBE20 the poly end is the same size as the thread.
The first number is the thread and the second number is the poly pipe. The HBE1520 is a 1/2" (15mm) thread with a 20mm poly end; the HBE2015 is a 3/4" (20mm) thread with a 15mm poly end. Hansen's product pages confirm this: the spare Poly Nut is the 20mm for the HBE1520 and the 15mm for the HBE2015.
| Stock | Sizes 15mm–50mm are stocked in store. We hold limited stock of other sizes, and can order them in if needed. |
| Delivery | Courier nationwide. Shipping is calculated at checkout based on your location. |
| Collections | Available from 21 Akatea Road, Glendene, Auckland. |
Body & nuts: high quality glass fibre reinforced nylon, UV stabilised. The AS/NZS 4020 test report lists the compound as Polyamide 6 Glass Fibre Reinforced (Durethan BKV 15F).
Hansen Easy Fit Poly Fittings from 15mm to 50mm have met the requirements of AS/NZS 4020:2018. The EasyFit and TrueFit range was tested at the Australian Water Quality Centre (report 356792, completed 7 March 2023).
Hansen lists the Easy Fit Poly range as fire rated UL94HB.
| Fitting Sizes | Max @ 20°C | kPa | psi |
|---|---|---|---|
| 15mm – 20mm (HBE) | 16 bar | 1,600 kPa | 235 psi |
Hansen rates Easy Fit Poly fittings PN16, a maximum working pressure of 16 bar at 20°C (68°F). Hansen tests its products for cold water use up to 60°C (140°F) and does not recommend use above that. Your pipe's own pressure rating may be lower, so check the pipe table below.
Full step-by-step guide, tightening and leak troubleshooting: Hansen poly fittings installation guide (Easy Fit Poly).
Hansen's Threaded Fitting Handy Tips: how to apply thread tape and tighten a threaded joint without over-tightening.
Technical documents are published by Hansen Products (NZ) Ltd.
| Hansen Code | Thread Outlet | Poly End | Spare Nut |
|---|---|---|---|
| HBE15 | BSPT 1/2" (15mm) | Poly 15mm (1/2") | 15mm Poly Nut |
| HBE20 | BSPT 3/4" (20mm) | Poly 20mm (3/4") | 20mm Poly Nut |
| HBE1520 | BSPT 1/2" (15mm) | Poly 20mm (3/4") | 20mm Poly Nut |
| HBE2015 | BSPT 3/4" (20mm) | Poly 15mm (1/2") | 15mm Poly Nut |
Thread Outlet is the BSPT thread for the tap (no nut). Poly End is the Easy Fit end with a barbed tail and Poly Nut. Sizes and codes are from Hansen's catalogue (BSPT thread size x pipe size); spare nuts are from Hansen's product pages. All are rated 16 bar at 20°C. Choose the code from the Size drop-down above. Hansen's website and catalogue don't publish dimension drawings for the HBE.
Hansen's Easy Fit Poly pipe specification: standard NZS 7601:1978 (New Zealand) polyethylene pipe (Type 3) for cold water service. Dimensions are in mm.
| Nominal Bore | Inside Diameter | Outside Diameter | Wall Thickness | Pipe Working Pressure |
|---|---|---|---|---|
| 15 | 11.7–12.7 | 16.9–17.3 | 2.3–2.6 | 0.90 MPa (130.50 psi) |
| 20 | 17.9–19.2 | 24.9–25.4 | 3.1–3.5 | 0.80 MPa (116.00 psi) |
| 25 | 24.2–25.6 | 31.2–31.8 | 3.1–3.5 | 0.65 MPa (94.25 psi) |
| 32 | 30.5–31.9 | 37.5–38.1 | 3.1–3.5 | 0.50 MPa (72.50 psi) |
| 40 | 36.8–38.3 | 43.8–44.5 | 3.1–3.5 | 0.45 MPa (65.25 psi) |
| 50 | 49.5–51.0 | 56.5–57.2 | 3.1–3.5 | 0.35 MPa (50.75 psi) |
Hansen Easy Fit Poly fittings are designed for all sizes of New Zealand LDPE, EnduroFlex, Australian Rural (Class B) and Irish imperial pipe (including washdown hose and non toxic tube). They also suit other flexible pipe and hose, such as thin wall irrigation tubing and rubber hoses.
Using your bracket elbows with anything other than water? Check Hansen's Easy Fit Poly chemical resistance ratings before you install. Bleach, halogens such as chlorine, strong acids and oxidising agents are rated "Bad", and pool and spa use is not covered by Hansen's warranty.
View Chemical Compatibility ChartStep-by-step Easy Fit Poly installation, a tightening guide, do's and don'ts and leak troubleshooting, straight from Hansen's instructions.
View Installation GuideHansen says it is used for connecting taps to low density poly pipe (LDPE) and EnduroFlex, and can also be used to connect taps to flexible pipe and hose.
One end is the BSPT thread outlet for the tap, with no nut. The other end is the Easy Fit poly end, with a barbed tail and Poly Nut, for the poly pipe.
Hansen lists it as a BSPT (tapered) thread for connecting taps but doesn't say whether it is male or female, so check the fitting against your tap before you buy.
The first number is the thread size and the second number is the poly pipe size, matching Hansen's "BSPT Thread Size x Pipe Size" listing. The HBE2015 is a 3/4" (20mm) BSPT thread with a 15mm poly end.
Yes. Hansen says to use either a thread sealing paste or tape on all threaded connections, and recommends Loctite 5331. The right sealant is non-hardening and compatible with plastic. Don't over-tighten the thread.
Hansen says to wind the nut by hand onto the pipe as tight as possible, then use a spanner or pipe grips to tighten until the nut is firm on the pipe.
New Zealand LDPE (low density polyethylene pipe), EnduroFlex, Australian Rural Class B, and Irish imperial polythene pipes, including washdown hose and non toxic tube.
Hansen designs Easy Fit Poly fittings for low density pipe. For medium density polyethylene pipe, Hansen makes its Easy Fit MD compression fittings, such as the MD Reducing Bracket Elbow (HMDRBE).
Yes. Hansen Easy Fit Poly fittings are made from a material approved for use with potable (drinkable) water, and fittings from 15mm to 50mm have met the requirements of AS/NZS 4020:2018 (Australian Water Quality Centre report 356792).
Hansen rates Easy Fit Poly fittings PN16, a maximum working pressure of 16 bar (1,600 kPa, 235 psi) at 20°C. Your pipe may have a lower rating; for example, Hansen's NZS 7601 LDPE table shows 0.90 MPa for 15mm pipe down to 0.35 MPa for 50mm.
Hansen tests all its products for cold water use up to a maximum of 60°C (140°F) and does not recommend use above that, as plastic expands as temperature rises. Products that fail above 60°C are not covered by Hansen's Limited Lifetime Warranty.
No. Hansen does not recommend the use of any Hansen Easy Fit fittings under any driveways, paths or foundations.
Yes. Hansen says Easy Fit Poly fittings are resistant to sea water, will not leach any substances harmful to marine life, and have provided excellent service in marine applications for many years.
No. Hansen says the high concentration of chlorine used in pool water will attack the material. The fitting material is only suitable for domestic water, and pool or spa use is not covered by Hansen's Limited Lifetime Warranty.
Yes. The nut is on the poly end; the thread outlet has no nut. Hansen lists a spare Poly Nut matching the poly pipe size, for example the 15mm Poly Nut for the HBE15 and the 20mm Poly Nut for the HBE1520.