HAN-HS15
$5.75 NZD
All prices include GST
Big Water Tanks is an official stockist of Hansen Products — New Zealand-made Easy Fit poly fittings for farm, irrigation, rural water and garden pipe. The Hansen Straight Coupling (HS) joins two lengths of low density poly pipe (LDPE) or EnduroFlex of the same size, in 6 sizes from 15mm (1/2") to 50mm (2"). The Long Straight Coupling (HLS) does the same job with a longer body, in 15mm, 20mm and 25mm.
A straight coupling is the simplest way to join two lengths of poly pipe or repair a break. Hansen describes it as "used for connecting Low Density Polyethylene Pipe (LDPE) and Enduroflex. Can also be used to connect flexible pipe and hose. Pipe Size x Pipe Size." It is a one piece fitting with no O-ring, no crimping and no solvent cement. Push the pipe onto the barbed tail and wind on the nut, and the barbs grip the inside of the pipe while the nut grips the outside. Hansen moulds the couplings in New Zealand from UV stabilised glass fibre reinforced nylon, and the Easy Fit Poly range is tested to AS/NZS 4020:2018 for contact with drinking water.
Use the standard HS to join two lengths of the same size poly pipe, extend a line, or connect flexible pipe or hose. It comes in every Easy Fit size from 15mm to 50mm.
The HLS is the long version of the HS, with a longer body between the two nuts. It's handy for repairing damaged pipe. Once you cut out the bad section, the extra length of the fitting helps make up the gap, so you don't have to stretch the pipe ends to meet. The HLS comes in 15mm, 20mm and 25mm.
Hansen's repair tip: when making a repair in a burst pipe, make sure the length of the cut away matches the length of the replacement fitting between the screwed on nuts.
Both ends are the same size ("pipe size x pipe size"). Hansen's sizes are nominal poly pipe sizes: 15mm = 1/2", 20mm = 3/4", 25mm = 1", 32mm = 1 1/4", 40mm = 1 1/2", 50mm = 2". To join two different sizes, use a Hansen Reducing Straight Coupling (HRS).
| Stock | Sizes 15mm–50mm are stocked in store. We hold limited stock of other sizes, and can order them in if needed. |
| Delivery | Courier nationwide. Shipping is calculated at checkout based on your location. |
| Collections | Available from 21 Akatea Road, Glendene, Auckland. |
Body & nuts: high quality glass fibre reinforced nylon, UV stabilised. The AS/NZS 4020 test report lists the compound as Polyamide 6 Glass Fibre Reinforced (Durethan BKV 15F).
Hansen Easy Fit Poly Fittings from 15mm to 50mm have met the requirements of AS/NZS 4020:2018. The EasyFit and TrueFit range was tested at the Australian Water Quality Centre (report 356792, completed 7 March 2023).
Hansen lists the Easy Fit Poly range as fire rated UL94HB.
| Fitting Sizes | Max @ 20°C | kPa | psi |
|---|---|---|---|
| 15mm – 50mm (HS & HLS) | 16 bar | 1,600 kPa | 235 psi |
Hansen rates Easy Fit Poly fittings PN16, a maximum working pressure of 16 bar at 20°C (68°F). Hansen tests its products for cold water use up to 60°C (140°F) and does not recommend use above that. Your pipe's own pressure rating may be lower, so check the pipe table below.
Full step-by-step guide, tightening and leak troubleshooting: Hansen poly fittings installation guide (Easy Fit Poly).
Technical documents are published by Hansen Products (NZ) Ltd.
| Hansen Code | Type | Metric | Imperial | Max @ 20°C |
|---|---|---|---|---|
| HS15 | Straight | 15mm x 15mm | 1/2" x 1/2" | 16 bar |
| HS20 | Straight | 20mm x 20mm | 3/4" x 3/4" | 16 bar |
| HS25 | Straight | 25mm x 25mm | 1" x 1" | 16 bar |
| HS32 | Straight | 32mm x 32mm | 1 1/4" x 1 1/4" | 16 bar |
| HS40 | Straight | 40mm x 40mm | 1 1/2" x 1 1/2" | 16 bar |
| HS50 | Straight | 50mm x 50mm | 2" x 2" | 16 bar |
| HLS15 | Long straight | 15mm x 15mm | 1/2" x 1/2" | 16 bar |
| HLS20 | Long straight | 20mm x 20mm | 3/4" x 3/4" | 16 bar |
| HLS25 | Long straight | 25mm x 25mm | 1" x 1" | 16 bar |
Sizes and codes are from Hansen's catalogue. Choose the code from the Size drop-down above. Hansen's website and catalogue don't publish dimension drawings for the HS and HLS.
Hansen's Easy Fit Poly pipe specification: standard NZS 7601:1978 (New Zealand) polyethylene pipe (Type 3) for cold water service. Dimensions are in mm.
| Nominal Bore | Inside Diameter | Outside Diameter | Wall Thickness | Pipe Working Pressure |
|---|---|---|---|---|
| 15 | 11.7–12.7 | 16.9–17.3 | 2.3–2.6 | 0.90 MPa (130.50 psi) |
| 20 | 17.9–19.2 | 24.9–25.4 | 3.1–3.5 | 0.80 MPa (116.00 psi) |
| 25 | 24.2–25.6 | 31.2–31.8 | 3.1–3.5 | 0.65 MPa (94.25 psi) |
| 32 | 30.5–31.9 | 37.5–38.1 | 3.1–3.5 | 0.50 MPa (72.50 psi) |
| 40 | 36.8–38.3 | 43.8–44.5 | 3.1–3.5 | 0.45 MPa (65.25 psi) |
| 50 | 49.5–51.0 | 56.5–57.2 | 3.1–3.5 | 0.35 MPa (50.75 psi) |
Hansen Easy Fit Poly fittings are designed for all sizes of New Zealand LDPE, EnduroFlex, Australian Rural (Class B) and Irish imperial pipe (including washdown hose and non toxic tube). They also suit other flexible pipe and hose, such as thin wall irrigation tubing and rubber hoses.
Using your couplings with anything other than water? Check Hansen's Easy Fit Poly chemical resistance ratings before you install. Bleach, halogens such as chlorine, strong acids and oxidising agents are rated "Bad", and pool and spa use is not covered by Hansen's warranty.
View Chemical Compatibility ChartStep-by-step Easy Fit Poly installation, a tightening guide, do's and don'ts and leak troubleshooting, straight from Hansen's instructions.
View Installation GuideBoth join two lengths of the same size poly pipe. The HLS is the long version, with a longer body between the nuts. That makes it handy for repairs where you have cut out a damaged section of pipe and need the fitting to make up some of the lost length. The HS comes in 15mm, 20mm, 25mm, 32mm, 40mm and 50mm, and the HLS in 15mm, 20mm and 25mm.
Cut out the damaged section with pipe cutters, a knife or saw, making square cuts, and clean the burrs off. Hansen says to make sure the length of the cut away matches the length of the replacement fitting between the screwed on nuts. Then wind each nut fully back, push each pipe end onto the fitting as far as possible into the nut, and wind on and tighten the nuts.
Hansen says to wind the nut by hand onto the pipe as tight as possible, then use a spanner or pipe grips to tighten until the nut is firm on the pipe.
New Zealand LDPE (low density polyethylene pipe), EnduroFlex, Australian Rural Class B, and Irish imperial polythene pipes, including washdown hose and non toxic tube.
Hansen designs Easy Fit Poly fittings for low density pipe. For medium density polyethylene pipe, Hansen makes its Easy Fit MD compression fittings, such as the MD Straight Coupling (HMDC).
Yes. Hansen Easy Fit Poly fittings are made from a material approved for use with potable (drinkable) water, and fittings from 15mm to 50mm have met the requirements of AS/NZS 4020:2018 (Australian Water Quality Centre report 356792).
Hansen rates Easy Fit Poly fittings PN16, a maximum working pressure of 16 bar (1,600 kPa, 235 psi) at 20°C. Your pipe may have a lower rating; for example, Hansen's NZS 7601 LDPE table shows 0.90 MPa for 15mm pipe down to 0.35 MPa for 50mm.
Hansen tests all its products for cold water use up to a maximum of 60°C (140°F) and does not recommend use above that, as plastic expands as temperature rises. Products that fail above 60°C are not covered by Hansen's Limited Lifetime Warranty.
No. Hansen does not recommend the use of any Hansen Easy Fit fittings under any driveways, paths or foundations.
Yes. Hansen says Easy Fit Poly fittings are resistant to sea water, will not leach any substances harmful to marine life, and have provided excellent service in marine applications for many years.
No. Hansen says the high concentration of chlorine used in pool water will attack the material. The fitting material is only suitable for domestic water, and pool or spa use is not covered by Hansen's Limited Lifetime Warranty.
Yes. Hansen lists a spare Poly Nut in the matching size for each coupling, for example the 25mm Poly Nut for the HS25.