BMT-WDDP230
$120.00 NZD
All prices include GST
Big Water Tanks stocks the Rain Harvesting First Flush Carrot. It diverts the first, dirtiest flush of roof water away from your tank without a traditional storage chamber, then switches back to send clean water to the tank. NZ model WDDP230, for 80mm and 100mm pipe.
Rain Harvesting says: "Divert your initial roof run-off without the need for a traditional first flush storage chamber and ensure only the cleanest water reaches your tank. It does not require a chamber (unlike traditional first flush diverters) which makes installation easy. It takes up less space and looks great on your wall. It diverts the first 20L/5 Gal and is perfect for medium catchment areas with low to moderate pollution." It is the same Carrot used in our Total Rain all-in-one rain head and first flush diverter.
Rain Harvesting's guide says:
For best results and minimal maintenance, Rain Harvesting recommends fitting Leaf Eater rain heads on all your downpipes, such as the Leaf Eater® Advanced or Leaf Eater® Stream Original, to limit the leaves and debris that reach the diverter.
From Rain Harvesting's First Flush Carrot Installation and Specification Guide.
A first flush diverter keeps the dirtiest roof water out of your tank. Pair the Carrot with one of our Big Water Tanks water tanks, add a Leaf Eater rain head upstream, or choose the Total Rain, which combines a Leaf Eater Stream rain head and the Carrot in one. Browse the rest of our Rain Harvesting range.
Rain Harvesting: "The Carrot uses the Catch All Tee to prevent dirty water from 'skipping' over the First Flush unit and accidentally entering your rainwater tank. The clever design of The Carrot means that you can install a First Flush device without the need for a traditional chamber. The Carrot resets itself after each rainfall event."
Water from the roof comes in one side of the Catch All Tee (1). The first flush runs down through the Carrot to stormwater (10). Once the first flush has been diverted, the Carrot seals and water flows on through the tee to the tank (2).
The Carrot comes pre-assembled with Filling grommet A on the Carrot filler frame, Draining grommet 2 on the Carrot and the Wick blanking grommet. Rain Harvesting says this default setup is a good starting point to reliably divert an average amount of water with a longer reset time.

Numbers refer to the part reference chart in Rain Harvesting's First Flush Carrot Installation and Specification Guide.
The Filling grommet sets how much dirty water is diverted, and the Draining grommet sets how quickly the Carrot resets. Rain Harvesting recommends keeping the standard grommets (Filling A, Draining 2) for the first rain, then adjusting to suit once you have seen how the Carrot performs in your system.
| Filling Grommet | Dirty Water Diverted |
|---|---|
| C | More water diverted |
| A (fitted as standard) | Medium amount of water diverted |
| B | Less water diverted |
| Draining Grommet | Reset | Dirty Water | Maintenance |
|---|---|---|---|
| Wicking grommet | Longest reset | Least water diverted | Most regular maintenance |
| 1 | Long reset | Less water diverted | More regular maintenance |
| 2 (fitted as standard) | Medium | Medium | Medium |
| 3 | Quick reset | More water diverted | Less regular maintenance |
Should I choose the Wicking grommet? Rain Harvesting: "If you have very low rainfall intensities, the wicking grommet will provide the longest reset time, ensuring that you capture the most water possible. It will require more maintenance than the draining grommets (which is simple by just washing the wick out occasionally)."
Examples from Rain Harvesting:
Note: some combinations of filling and draining grommet are less compatible with typical rainfall events than others.
From the Flushing Guidelines in Rain Harvesting's First Flush Carrot Installation and Specification Guide. The guide lists Filling grommets A and B and Draining grommets 0 to 3 in the box. Not sure which setting suits your roof? ask us.
Rain Harvesting lists the NZ First Flush Carrot, WDDP230, for 80mm and 100mm pipe, with female / socket fittings for each size.
| NZ Pipe | A Fitting | Connection |
|---|---|---|
| 80mm | 80 F | Female / socket fitting: solvent weld the pipe into the Catch All Tee sockets |
| 100mm | 100 F | Female / socket fitting: solvent weld the pipe into the Catch All Tee sockets |
Sizes and fittings are from Rain Harvesting's First Flush Carrot Installation and Specification Guide and Rain Harvesting's NZ product page. If you're not sure what your pipework needs, ask us before you cut any pipe.
Tools you may need: tape measure, marker pen, saw, solvent weld glue, screws, and a drill or screwdriver.
1Check the setup
The Carrot comes pre-assembled with Filling grommet A, Draining grommet 2 and the Wick blanking grommet. This is a good starting point.
2Choose the spot
The Catch All Tee can go in a horizontal or vertical pipe, but the Carrot Diverter Chamber itself must be vertical (Figure 1).
3Orient the tee
In a horizontal pipe, point the arrow in the direction of water flow (Figure 1b). In a vertical pipe, always point the arrow up (Figure 1a). This sets which socket attaches to the Carrot.
4Fit the Catch All Tee
Measure and cut your pipe to make space for the tee, with clean, smooth edges. Solvent weld the incoming and outgoing sockets and pipe; leave the lower socket for now.
5Glue the Upper Collar
Apply solvent weld glue to the Carrot Upper Collar and the lower socket of the Catch All Tee, and insert it firmly.
6Screw on the housing
Make sure the O-ring is in the groove under the Upper Collar, then screw the Carrot housing into position.
7Pipe to stormwater
Slide the Carrot Lower Slip Coupling onto the outlet of the Carrot housing and fit the rest of the pipework. The first flush goes down this pipe, so route it to stormwater or another suitable place.
8First rain
Keep the standard grommets for the first rain. Once you have seen how it performs, adjust the grommets to suit (see the Grommet Guide).
Steps and Figure 1 from Rain Harvesting's First Flush Carrot Installation and Specification Guide.
| Code | Pipe | A Fitting | B | C | D |
|---|---|---|---|---|---|
| WDDP230 | 80mm | 80 F | 551 | 333 | 140 |
| WDDP230 | 100mm | 100 F | 526 | 283 | 140 |
NZ model. All dimensions in mm, from Rain Harvesting's First Flush Carrot Installation and Specification Guide; see the drawing for A to D. F = female / socket fitting.

The installation guide is published by Rain Harvesting by Blue Mountain Co.
First Flush Carrot: Product Overview
First Flush Carrot: What's in the Box
How to Install Your First Flush Carrot
First Flush Carrot: Adjusting How Much Water You Divert
Official videos from Rain Harvesting's YouTube channel.
The NZ model, WDDP230, is listed for 80mm and 100mm pipe, with female / socket fittings (80 F and 100 F).
Rain Harvesting sets it up to divert around 20L (5 gal). You can adjust this with the filling and draining grommets supplied in the kit.
No. The Carrot automatically diverts the water and seals without a chamber, which keeps it compact.
Yes. The Catch All Tee can be fitted horizontally or vertically; point the arrow in the direction of flow on a horizontal pipe, or up on a vertical pipe. The Carrot chamber itself must be vertical.
Down the pipe from the Carrot Lower Slip Coupling, so route that pipe to stormwater or another suitable place.
Start with the standard Filling grommet A and Draining grommet 2 for the first rain, then adjust using the Grommet Guide above. For very low rainfall intensity, Rain Harvesting suggests the wicking grommet.
Periodically unscrew the Carrot housing and check the grommets are not blocked, the spring works and the seals are seated. Leaf Eater rain heads on your downpipes cut down the debris reaching it.
Total Rain combines a Leaf Eater Stream rain head with the Carrot in one product for 80mm downpipe. The First Flush Carrot on its own fits into your existing pipework with its Catch All Tee.