Search

HAN-HBV15

Hansen - Ball Valves - HBV

Size
Spare Parts

Big Water Tanks is an official stockist of Hansen Products, made in New Zealand and trusted by Kiwi farmers for over 50 years. Hansen Full Flow Ball Valves (HBV) stop or start the flow of water with a quarter turn. Both ends are female BSPT threads, in 6 sizes from 15mm (1/2") to 50mm (2"). Choose a blue handle for general use or lilac for grey water. For a spare handle for a 15mm valve, please select the 20mm handle.

Hansen Full Flow Ball Valves, 15mm to 50mm Female BSPT

Hansen Full Flow Ball Valves can be used anywhere the flow of fluid needs to be stopped or started. The bore is full flow, so a 25mm valve has a 25mm bore and the valve doesn't restrict your flow. Each end is a female BSPT thread, so it screws onto a male thread or pipe fitting. Every valve is hand tested by Hansen before it leaves the factory.

Quick Facts

  • Sizes: 15mm, 20mm, 25mm, 32mm, 40mm and 50mm (1/2" to 2")
  • Threads: Female × Female BSPT, both ends
  • Pressure: 16 Bar (1600 kPa, 235 psi) @ 20°C
  • Temperature: Cold water, tested to a maximum of 60°C
  • Handles: Blue for general use or lilac for grey water; spare blue, green and lilac handles
  • Approvals: AS/NZS 4020 drinking water, WRAS, and IMCI marine approved
  • Stock: 15mm–50mm blue complete valves and blue handles stocked in store. Lilac valves and handles are ordered in
  • Warranty: Hansen Limited Lifetime Warranty

Sizes & Dimensions

Hansen HBV ball valve dimension drawing, letters A to E
  • AOverall length, end to end
  • BOverall height, base to top of handle
  • CHandle length
  • DBody diameter
  • ECentre of bore to top of handle
  • T1Female BSPT thread, end 1
  • T2Female BSPT thread, end 2
Code T1 & T2 (BSPT female) A (mm) B (mm) C (mm) D (mm) E (mm)
HBV15 15mm (1/2") 98 82 93 56 54
HBV20 20mm (3/4") 98 82 93 56 54
HBV25 25mm (1") 111 93 104 65 61
HBV32 32mm (1 1/4") 122 107 112 76 69
HBV40 40mm (1 1/2") 135 124 123 90 79
HBV50 50mm (2") 146 140 131 106 89

Lilac handle valves use the same codes with an L, for example HBVL25, and the same dimensions. Dimensions from Hansen Products.

Key Features & Benefits

  • Full flow bore: A 25mm valve has a 25mm bore, so you keep your flow.
  • Positive "click": A smooth open and close action helps reduce surge, which can damage your system, and the click tells you the valve is either on or off.
  • Frost Friendly: Tested by Hansen in frost conditions. Results may vary in freezing conditions.
  • Won't rust or corrode: Non-corrosive, UV stabilised materials for general or salt water applications.
  • Drinking water and marine approved: Meets AS/NZS 4020 and WRAS, and IMCI approved to ISO 9093-2 (Recreational Craft Directive 94/25/EC), so it is safe in salt water environments.
  • Removable handle: Take the handle off for security or tight spaces.
  • Colour coded handles: Blue for general applications, lilac for grey water, green for extra visibility or to tell lines apart.
  • Hand tested: Every valve is hand tested by Hansen. New Zealand made.

Maintenance

Removing the handle: turn the handle slightly clockwise, then put your fingers under the handle and pull it off while pushing down on the valve body with your thumbs.

1. Turn slightly clockwise

Removing a Hansen ball valve handle: turn it slightly clockwise

2. Pull the handle off

Removing a Hansen ball valve handle: pull it off

Open or closed? With the handle off, check the notch in the centre of the stem. The valve is open when the notch is not parallel with the body, and closed when it is parallel with the body.

Open: notch across the body

Hansen ball valve stem notch across the body, valve open

Closed: notch in line with the body

Hansen ball valve stem notch in line with the body, valve closed

Options & Spare Handles

Each size is available as a complete valve or a spare handle:

  • Complete Blue: Ball valve with a blue handle (HBV15 to HBV50), for general use.
  • Complete Lilac: Ball valve with a lilac handle (HBVL15 to HBVL50), for grey water. Ordered in.
  • Blue, Green or Lilac Handle: Spare handle only, no valve. Blue handles are stocked; lilac handles are ordered in.

15mm valves use the 20mm handle. For a spare handle for a 15mm valve, please select the 20mm handle.

Size Code (blue) Code (lilac) Thread
15mm HBV15 HBVL15 1/2" BSPT female
20mm HBV20 HBVL20 3/4" BSPT female
25mm HBV25 HBVL25 1" BSPT female
32mm HBV32 HBVL32 1 1/4" BSPT female
40mm HBV40 HBVL40 1 1/2" BSPT female
50mm HBV50 HBVL50 2" BSPT female

Pressure & Flow

Code Max pressure @ 20°C Kv value Cv value (Imp gal)
HBV15 16 Bar (235 psi) 28.74 27.65
HBV20 16 Bar (235 psi) 35.95 34.61
HBV25 16 Bar (235 psi) 51.37 49.42
HBV32 16 Bar (235 psi) 141.55 136.24
HBV40 16 Bar (235 psi) 225.53 217.04
HBV50 16 Bar (235 psi) 469.48 452.05

Flow coefficients from independent tests by The University of Auckland, published by Hansen. Hansen tests all its products with cold water up to a maximum of 60°C (140°F).

Good to Know

  • Female both ends: To connect to a female port, add a Hex Nipple (HSN) or Reducing Hex Nipple (HRHN). Need a male thread on one end? See the Male/Female Ball Valve (HBVMF), 25mm to 50mm.
  • Stock: We stock blue complete valves and blue handles in store. Lilac valves and handles are ordered in.
  • Not for pools or spas: The high level of chlorine in pool and spa water attacks the material, and Hansen's warranty doesn't cover this use.
  • Hot water: Not above 60°C. Hansen doesn't cover failures above 60°C under warranty.
  • In our hose kits: Hansen ball valves are the shut-off valves in our Water Tank Hose Kits.

Installation in Brief

1a. PTFE thread tape

Hansen ball valve install step 1a: PTFE thread tape on the male thread

1b. Or thread sealant

Hansen ball valve install step 1b: thread sealant on the male thread

2. Screw in

Hansen ball valve install step 2: screwing the pipe into the valve

3. Tighten, no more

Hansen ball valve install step 3: tightening one to two turns with a spanner

1Seal the thread

Use a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331) or PTFE thread tape on all threaded connections.

2Screw in

Screw the pipe or male fitting into the valve.

3Don't over-tighten

Finger tight, then one to two turns with a spanner. No more.

4Support your pipework

All pipe work must be adequately supported.

Hansen's Ball Valve Handy Tips video.

Steps, photos and video from Hansen. More tips in our Hansen threaded fitting installation guide.

Specifications

Specification Detail
Threads Female × Female BSPT
Sizes 15mm, 20mm, 25mm, 32mm, 40mm, 50mm (1/2", 3/4", 1", 1 1/4", 1 1/2", 2")
Pressure rating 16 Bar (1600 kPa, 235 psi) @ 20°C
Temperature Cold water, tested to a maximum of 60°C (140°F)
Body, end caps & handle Glass fibre reinforced nylon
Ball Polypropylene
Ball seats & stem Acetal (POM)
O-rings EPDM
Approvals AS/NZS 4020, WRAS, IMCI (ISO 9093-2, Recreational Craft Directive 94/25/EC)
Fire rating UL94HB
Warranty Hansen Limited Lifetime Warranty
Made in New Zealand

Chemical Resistance

Hansen ball valves are suited to domestic water. Check Hansen's chemical resistance chart before using them with anything else. For Hansen threaded and poly fittings, see our Hansen chemical compatibility page.

Ball Valve Chemical Resistance Chart

Frequently Asked Questions

How tight should I tighten my Hansen ball valve?

Do not over-tighten. Finger tight plus one to two turns, no more. See our Hansen threaded fitting installation guide.

What thread sealant should I use?

Use a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331) or PTFE thread tape on all threaded connections. Hansen also lists Ceelon PTFE tape.

Which end is the thread?

Both ends are female BSPT threads. For a male thread on one end, see the Male/Female Ball Valve (HBVMF).

How can I tell if the valve is open or closed?

Look at the notch in the centre of the stem. Open: the notch is not parallel with the body. Closed: the notch is parallel with the body.

Which colours do you stock?

We stock blue complete valves and blue spare handles in store. Lilac valves and handles are ordered in.

Which spare handle fits a 15mm valve?

The 20mm handle. Please select the 20mm handle for a 15mm valve.

Can I use Hansen ball valves with metal fittings?

Yes.

Do I need to support my ball valve?

Yes. All pipe work must be adequately supported.

Can I use it in my swimming pool or spa?

No. The high concentration of chlorine in pool water attacks the material, and Hansen's warranty doesn't cover this use. The valves are suited to domestic water.

What temperature can I use it at?

Hansen tests its products with cold water up to a maximum of 60°C (140°F) and doesn't recommend higher temperatures, as plastic expands with heat. Failures above 60°C aren't covered by warranty.

Are Hansen ball valves frost friendly?

Yes. Hansen has tested them in frost conditions. Results may vary in freezing conditions.