Search

HAN-HBV25MF

Hansen - Blue Handle Male/Female Threaded Ball Valve - HBV HBVMF

Hansen Code

Big Water Tanks is an official stockist of Hansen Products, made in New Zealand and trusted by Kiwi farmers for over 50 years. The Hansen Male/Female Full Flow Ball Valve (HBVMF) stops or starts the flow of water with a quarter turn. One end is a female BSPT thread and the other is a male BSPT thread, so it screws straight into a female port without an extra nipple. 4 sizes from 25mm (1") to 50mm (2"), with a blue handle.

Hansen Male/Female Full Flow Ball Valves, 25mm to 50mm BSPT

Hansen Full Flow Ball Valves can be used anywhere the flow of fluid needs to be stopped or started. The bore is full flow, so a 25mm valve has a 25mm bore and the valve doesn't restrict your flow. On the HBVMF, one end is female (it screws onto a male thread) and the other end is male (it screws into a female thread or port). Need female threads on both ends, or sizes from 15mm? See the Hansen Female Ball Valve (HBV). Every valve is hand tested by Hansen before it leaves the factory.

Quick Facts

  • Sizes: 25mm, 32mm, 40mm and 50mm (1" to 2")
  • Threads: Male × Female BSPT: one female end, one male end
  • Pressure: 16 Bar (235 psi) @ 20°C
  • Temperature: Cold water, tested to a maximum of 60°C
  • Handle: Blue, for general use. Removable
  • Approvals: AS/NZS 4020 drinking water, WRAS, and IMCI marine approved
  • Stock: Blue complete valves and blue handles are stocked in store. Lilac handles are ordered in.
  • Warranty: Hansen Limited Lifetime Warranty

Sizes & Dimensions

Hansen HBVMF male/female ball valve dimension drawing, letters A to E
  • AOverall length, end to end
  • BOverall height, base to top of handle
  • CHandle length
  • DBody diameter
  • ECentre of bore to top of handle
  • T1Female BSPT thread end
  • T2Male BSPT thread end
Code T1 female & T2 male (BSPT) A (mm) B (mm) C (mm) D (mm) E (mm)
HBV25MF 25mm (1") 131 93 104 65 61
HBV32MF 32mm (1 1/4") 142 107 112 76 69
HBV40MF 40mm (1 1/2") 155 124 123 90 79
HBV50MF 50mm (2") 170 140 131 106 89

Dimensions from Hansen Products.

Key Features & Benefits

  • Male and female ends: Screws straight into a female port or fitting on one side and onto a male thread on the other, so you need one less fitting.
  • Full flow bore: A 25mm valve has a 25mm bore, so you keep your flow.
  • Positive "click": A smooth open and close action helps reduce surge, which can damage your system, and the click tells you the valve is either on or off.
  • Frost Friendly: Tested by Hansen in frost conditions. Results may vary in freezing conditions.
  • Won't rust or corrode: Non-corrosive materials for general or salt water applications.
  • Drinking water and marine approved: Hansen ball valves meet AS/NZS 4020 and WRAS, and are IMCI approved to ISO 9093-2 (Recreational Craft Directive 94/25/EC).
  • Removable handle: Take the handle off for security or tight spaces.
  • Hand tested: Every valve is hand tested by Hansen. New Zealand made.

Maintenance

Removing the handle: turn the handle slightly clockwise, then put your fingers under the handle and pull it off while pushing down on the valve body with your thumbs.

1. Turn slightly clockwise

Removing a Hansen ball valve handle: turn it slightly clockwise

2. Pull the handle off

Removing a Hansen ball valve handle: pull it off

Open or closed? With the handle off, check the notch in the centre of the stem. The valve is open when the notch is not parallel with the body, and closed when it is parallel with the body.

Open: notch across the body

Hansen ball valve stem notch across the body, valve open

Closed: notch in line with the body

Hansen ball valve stem notch in line with the body, valve closed

Threads & Spare Handles

Each valve has a female BSPT thread on one end (T1) and a male BSPT thread on the other (T2), both the same size.

Code Female end (T1) Male end (T2)
HBV25MF 25mm (1") BSPT 25mm (1") BSPT
HBV32MF 32mm (1 1/4") BSPT 32mm (1 1/4") BSPT
HBV40MF 40mm (1 1/2") BSPT 40mm (1 1/2") BSPT
HBV50MF 50mm (2") BSPT 50mm (2") BSPT

Spare handles: The HBVMF uses the same handles as the Hansen Ball Valve (HBV) of the same size. Spare blue, green and lilac handles are available on the HBV page. Blue complete valves and blue handles are stocked in store. Lilac handles are ordered in.

Good to Know

  • Which end is which: The female end (T1) screws onto a male thread. The male end (T2) screws into a female thread or port.
  • Female both ends or smaller sizes: See the Hansen Ball Valves (HBV), female × female from 15mm to 50mm, with blue or lilac handles.
  • Spare handles: The HBVMF uses the same handles as the Hansen Ball Valve (HBV) of the same size. Spare blue, green and lilac handles are available on the HBV page.
  • Stock: Blue complete valves and blue handles are stocked in store. Lilac handles are ordered in.
  • Not for pools or spas: The high level of chlorine in pool and spa water attacks the material, and Hansen's warranty doesn't cover this use.
  • Hot water: Not above 60°C. Hansen doesn't cover failures above 60°C under warranty.

Installation in Brief

1a. PTFE thread tape

Hansen ball valve install step 1a: PTFE thread tape on the male thread

1b. Or thread sealant

Hansen ball valve install step 1b: thread sealant on the male thread

2. Screw in

Hansen ball valve install step 2: screwing the pipe into the valve

3. Tighten, no more

Hansen ball valve install step 3: tightening one to two turns with a spanner

1Seal the male threads

Use a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331) or PTFE thread tape on all threaded connections, including the valve's own male end.

2Screw in

Screw the male end into your female port or fitting, and screw your pipe or male fitting into the female end.

3Don't over-tighten

Finger tight, then one to two turns with a spanner. No more.

4Support your pipework

All pipe work must be adequately supported.

Hansen's Ball Valve Handy Tips video.

Steps, photos and video from Hansen (shown on the female × female valve). More tips in our Hansen threaded fitting installation guide.

Specifications

Specification Detail
Threads Male × Female BSPT
Sizes 25mm, 32mm, 40mm, 50mm (1", 1 1/4", 1 1/2", 2")
Pressure rating 16 Bar (235 psi) @ 20°C
Temperature Cold water, tested to a maximum of 60°C (140°F)
Body, end caps & handle Glass fibre reinforced nylon
Ball Polypropylene
Ball seats & stem Acetal (POM)
O-rings EPDM
Approvals AS/NZS 4020, WRAS, IMCI (ISO 9093-2, Recreational Craft Directive 94/25/EC)
Warranty Hansen Limited Lifetime Warranty
Made in New Zealand

Chemical Resistance

Hansen ball valves are suited to domestic water. Check Hansen's chemical resistance chart before using them with anything else. For Hansen threaded and poly fittings, see our Hansen chemical compatibility page.

Ball Valve Chemical Resistance Chart

Frequently Asked Questions

Which end is the male thread?

One end is a female BSPT thread (T1 on the drawing) and the other is a male BSPT thread (T2). Both ends are the same size.

Do you have a female × female version?

Yes, the Hansen Ball Valves (HBV), from 15mm to 50mm.

How tight should I tighten my Hansen ball valve?

Do not over-tighten. Finger tight plus one to two turns, no more. See our Hansen threaded fitting installation guide.

What thread sealant should I use?

Use a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331) or PTFE thread tape on all threaded connections. Hansen also lists Ceelon PTFE tape.

How can I tell if the valve is open or closed?

Look at the notch in the centre of the stem. Open: the notch is not parallel with the body. Closed: the notch is parallel with the body.

Which colours do you stock?

Blue complete valves and blue handles are stocked in store. Lilac handles are ordered in.

Where can I get a spare handle?

The HBVMF uses the same handles as the Hansen Ball Valve (HBV) of the same size. Spare blue, green and lilac handles are available on the HBV page. Blue complete valves and blue handles are stocked in store. Lilac handles are ordered in.

Can I use Hansen ball valves with metal fittings?

Yes.

Do I need to support my ball valve?

Yes. All pipe work must be adequately supported.

Can I use it in my swimming pool or spa?

No. The high concentration of chlorine in pool water attacks the material, and Hansen's warranty doesn't cover this use. The valves are suited to domestic water.

What temperature can I use it at?

Hansen tests its products with cold water up to a maximum of 60°C (140°F) and doesn't recommend higher temperatures, as plastic expands with heat. Failures above 60°C aren't covered by warranty.

Are Hansen ball valves frost friendly?

Yes. Hansen has tested them in frost conditions. Results may vary in freezing conditions.