Search

HAN-HFV25

Hansen - Foot Valve and Socks - HFV

Size

Big Water Tanks is an official stockist of Hansen Products, made in New Zealand and trusted by Kiwi farmers for over 50 years. The Hansen Foot Valve (HFV) goes on the end of your pump's suction line, in a dam, stream or buried tank. It stops the line emptying when the pump turns off, so you don't need to prime your pump at start up. Female BSPT thread, in 5 sizes from 25mm (1") to 63mm (2 1/2"). Filter socks and diaphragm & spring kits are available here too.

Hansen Foot Valves, 25mm to 63mm Female BSPT

Hansen Foot Valves are used on the end of a suction line to stop fluids in the line emptying when the pump is turned off, thus eliminating the need to prime your pump at start up. Typical uses are pumping from a dam, stream or river, and from a buried (underground) tank. Hansen says the valve delivers high volumes of water quickly with unrestricted full flow, works at any angle or position, and can be serviced through its screw cap without taking it out of the line.

Quick Facts

  • Sizes: 25mm, 32mm, 40mm, 50mm and 63mm (1" to 2 1/2")
  • Thread: Female BSPT, screws onto the end of your suction pipe
  • Pressure: 16 Bar (232 psi) maximum working pressure @ 20°C
  • Temperature: Cold water, tested to a maximum of 60°C
  • Fitting: Works at any angle or position
  • Servicing: Screw cap; diaphragm and spring swap with the same size Hansen Check Valve
  • Approvals: AS/NZS 4020:2018 drinking water
  • Stock: HFV25 to HFV50 foot valves are stocked in store. The 63mm (HFV63) is ordered in. Filter socks and spare kits are available here; ask us about stock
  • Warranty: Hansen Limited Lifetime Warranty

Sizes & Dimensions

Hansen HFV foot valve dimension drawing, lettered A to D and T1
  • AOverall width
  • BOverall height (25mm to 50mm)
  • COverall height including lugs (63mm)
  • DLugs, on 63mm valves only
  • T1Female BSPT thread
Code T1 (BSPT female) A (mm) B (mm) C (mm)
HFV25 1" (25mm) 69 72 –
HFV32 1 1/4" (32mm) 87 88 –
HFV40 1 1/2" (40mm) 99 99 –
HFV50 2" (50mm) 123 120 –
HFV63 2 1/2" (63mm) 152 – 156

Dimensions from Hansen Products, who list these valves as FV25 to FV63.

Key Features & Benefits

  • Keeps your pump primed: Stops the suction line emptying when the pump turns off.
  • Full flow: High volumes of water quickly with unrestricted full flow. Hansen quotes an efficiency in excess of 95% compared to many other types of valves.
  • Any angle: Operates via pressure differential, at any angle or position: upside down, on its side, or straight up and down.
  • No poppet: No poppet valve to wear or jam. Smooth operating valve for high efficiency.
  • Self cleaning: Unique design with a self-cleaning diaphragm, and blockages are reduced due to low fluid velocity through the slots.
  • Easy in-line servicing: Screw cap access to all moving parts. The diaphragm and spring are interchangeable with the same size Hansen Check Valve.
  • Built to last: Strong, non-corrosive, UV stabilised materials. Materials approved for use with potable (drinkable) water.
  • Hand tested: All Hansen Foot Valves are rigorously hand tested. New Zealand made.

Maintenance

You don't need to remove the valve from the line to service it. If grit or debris has reduced its working efficiency, unscrew the cap and clean out the valve. Replace the diaphragm if it is damaged; spare diaphragm & spring kits (HVD) are available here.

Hansen HFV foot valve parts diagram, lettered A to G
  • ASpigot
  • BLugs (63mm valve only)
  • CCap
  • DSpring
  • EPin
  • FDiaphragm
  • GBody

Re-assembly (make sure all parts are fully cleaned first):

  • Turn the foot valve body upside down.
  • Seat the diaphragm into the valve body.
  • If the spring was removed, place it over the pin and turn it anti-clockwise while pushing firmly to retain it on the spigot.
  • Place the cap onto the valve body.
  • Screw the cap fully onto the body and tighten down, hand tight only. For the 63mm valve, use the lugs to tighten the cap a further 1/4 to 1/3 turn until it stops.

Hansen's Foot & Check Valve Handy Tips video.

Filter Socks & Spare Kits

As well as the valves, this page has filter socks and spare diaphragm & spring kits:

Code What it is Fits
HFVFS Foot valve filter sock HFV25, HFV32, HFV40
HFVFSL Foot valve filter sock (large) HFV50, HFV63
HVD25 Diaphragm & spring kit HFV25 or HCV25
HVD32 Diaphragm & spring kit HFV32 or HCV32
HVD40 Diaphragm & spring kit HFV40 or HCV40
HVD50 Diaphragm & spring kit HFV50 or HCV50
HVD63 Diaphragm & spring kit HFV63 or HCV63

Filter sock: fits over the foot valve to help filter and stop particles entering the valve. Hansen says it also discourages the build up of some menacing forms of marine life.

Stock: HFV25 to HFV50 foot valves are stocked in store. The 63mm (HFV63) is ordered in. For socks and spare kits, ask us.

Choosing the Right Size

Don't just match the valve to your pipe size. Work out your pump's flow (your pump installer or supplier can help), find it along the bottom of the chart, then go up to the size valve with an acceptable head loss for your system. Because the Hansen Foot Valve is so efficient, the size you need is often smaller than your pipe.

Hansen foot valve sizing chart: head loss against flow rate for FV25 to FV63

Example from Hansen: at 400 litres per minute, an FV40 has a head loss of 1.8m and an FV32 a head loss of 3.3m.

Dirty water: choose the smallest valve that will be operating in the area shown by the thicker line, with an acceptable head loss. The higher velocity across the diaphragm helps the valve self clean.

Code Kv value Cv value (Imp gal)
HFV25 24.66 23.72
HFV32 43.18 41.56
HFV40 57.14 54.99
HFV50 92.97 89.46
HFV63 147.24 141.69

Chart and flow coefficients from independent tests by The University of Auckland, published by Hansen.

Good to Know

  • Foot valve or check valve? A foot valve goes on the end of the suction line, in the water, to keep the line full and your pump primed. For a non-return valve inline in your pipework, see the Hansen Check Valve (HCV). Both use the same diaphragm & spring kit in the same size.
  • Keep it off the bottom: Once installed, make sure the foot valve is raised up off the surface of the water bed to help prevent debris entering the valve and damaging your pump.
  • Shallow streams and sand: Hansen doesn't advise pumping sand. Because the valve works at any angle, you may be able to install it vertically above your suction pipe to keep it above the sand.
  • Salt water: The spring is stainless steel and may eventually corrode in salt water. It is available as a replacement part. All other parts are fully resistant to salt water.
  • Stock: HFV25 to HFV50 foot valves are stocked in store. The 63mm (HFV63) is ordered in.
  • Pumping from an above-ground tank? Our Water Tank Hose Kits connect the tank outlet to your pump.
  • Not for pools or spas, or above 60°C: Chlorine attacks the material, and Hansen's warranty doesn't cover pool and spa use or failures above 60°C.

Installation in Brief

1Choose your size

Use the sizing chart above to pick the valve for your pump's flow.

2Seal the thread

Use a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331) or PTFE thread tape on all threaded connections.

3Connect to your pipe

Connect the valve directly to the end of a threaded pipe, or use a Hansen Male Straight or Reducing Straight Coupling to connect to your pipe.

4Don't over-tighten

Hand tight plus a maximum of two turns with tools.

5Support your pipework

All pipe work must be adequately supported. The valve can be installed at any angle.

6Raise it off the bed

Make sure the foot valve is raised up off the surface of the water bed to help keep debris out of the valve and your pump.

Hansen's Foot Valve Installation Handy Tips video.

Steps and video from Hansen. More tips in our Hansen threaded fitting installation guide.

Specifications

Specification Detail
Thread Female BSPT (NPT available from Hansen as a non-stock item on request)
Sizes 25mm, 32mm, 40mm, 50mm, 63mm (1", 1 1/4", 1 1/2", 2", 2 1/2")
Maximum working pressure 16 Bar (232 psi) @ 20°C
Temperature Cold water, tested to a maximum of 60°C (140°F)
Body High quality glass fibre reinforced nylon
Diaphragm Nitrile rubber
Spring Stainless steel (302 grade)
Approvals AS/NZS 4020:2018
Warranty Hansen Limited Lifetime Warranty
Made in New Zealand

Chemical Resistance

Hansen foot valves are suited to domestic water. Check Hansen's foot and check valve chemical resistance chart before using them with anything else. For Hansen threaded and poly fittings, see our Hansen chemical compatibility page.

Foot & Check Valve Chemical Resistance Chart

Downloads

Foot Valve Brochure & FAQ (PDF) Foot Valve Info Sheet (PDF) AS/NZS 4020 Test Report (PDF)

Technical documents are published by Hansen Products (NZ) Ltd.

Frequently Asked Questions

What does a foot valve do?

It goes on the end of a suction line and stops the line emptying when the pump is turned off, so you don't need to prime your pump at start up.

Do I choose a valve to match my suction pipe size?

Not necessarily. Because of the Hansen Foot Valve's higher efficiency, you match your flow with the head loss your pump can afford, and the valve size is often smaller than the pipe. See the sizing chart above.

I'm replacing an existing 40mm valve. Do I use the same size?

Use the sizing chart to work out the size. In some situations you may be able to use a smaller Hansen valve than your existing non-Hansen valve.

My dam gets dirty with slime and weed. Will it cope?

Yes. Hansen designed the foot valve to work in dirty water. Because of its lower head loss you can choose a smaller size, and the higher velocity across the diaphragm makes the valve self cleaning.

My stream is shallow and I pump some sand. Will it wear out?

Pumping sand isn't advisable because it damages your pump. With the screw cap you only need to replace the parts that wear, and because the valve works at any angle you may be able to install it vertically above your suction pipe to keep it above the sand.

Do I have to remove the valve from the line to service it?

No. You can service it inline through the screw cap. See Maintenance above.

Why won't my valve seal?

Something may be sitting between the diaphragm and its seat: pull the valve apart and clean it out, replacing the diaphragm if damaged. Also check you are using the correct size valve for your flow.

Can I use it with salt water?

The spring is 302 grade stainless steel and may eventually corrode in salt water; it is available as a replacement part. All other parts are fully resistant to salt water.

Which filter sock do I need?

HFVFS fits the 25mm to 40mm foot valves. HFVFSL fits the 50mm and 63mm foot valves.

Which sizes do you stock?

HFV25 to HFV50 foot valves are stocked in store. The 63mm (HFV63) is ordered in. For filter socks and spare kits, ask us.

What thread sealant should I use?

Use a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331) or PTFE thread tape on all threaded connections. Hand tight plus a maximum of two turns with tools.

What temperature can I use it at?

Hansen tests its products with cold water up to a maximum of 60°C (140°F). Failures above 60°C aren't covered by warranty.

Can I use it in my swimming pool or spa?

No. The high concentration of chlorine in pool water attacks the material, and Hansen's warranty doesn't cover this use.