Search

HAN-HFT15

Hansen - Female Threaded Tee Connector - HFT

Size

Big Water Tanks is an official stockist of Hansen Products — New Zealand-made Easy Fit poly fittings for farm, irrigation, rural water and garden pipe. The Hansen Female Threaded Tee Connector (HFT) has two Easy Fit poly ends on the run, each with a barbed tail and Poly Nut, and a female BSPT thread on the middle (branch) outlet. The middle is a thread, not a poly nut. It comes in 6 sizes from 15mm (1/2") to 50mm (2").

Hansen Easy Fit Poly Female Threaded Tee Connector (HFT): Poly Pipe Tee to Male Thread

A female threaded tee lets you take a threaded connection, such as a male threaded fitting, valve or riser, off a poly pipe line. The two run ends are Easy Fit poly ends: push the pipe onto the barbed tail and wind on the Poly Nut, and the barbs grip the inside of the pipe while the nut grips the outside. The middle (branch) outlet is a female BSPT (tapered) thread with no nut, which a male thread screws into. Hansen describes the HFT as "used for connecting Low Density Polyethylene Pipe (LDPE) and Enduroflex to Male Threads. Can also be used to connect flexible pipe and hose. BSPT Thread Size x Pipe Size x Pipe Size." The poly ends are one piece with no O-ring, no crimping and no solvent cement. Hansen moulds its Easy Fit fittings in New Zealand from UV stabilised glass fibre reinforced nylon, and the Easy Fit Poly range is tested to AS/NZS 4020:2018 for contact with drinking water.

Quick Facts

  • Run ends (both): Easy Fit poly pipe, barbed tail and Poly Nut
  • Middle (branch) outlet: Female BSPT thread, not a poly nut
  • Sizes: HFT15, HFT20, HFT25, HFT32, HFT40 and HFT50: the middle thread and both poly run ends are the same size (15mm to 50mm)
  • Thread sealant: Seal the threaded joint with paste or tape. Hansen recommends Loctite 5331
  • Fits: NZ low density poly pipe (LDPE), EnduroFlex, Australian Rural (Class B) and Irish imperial pipe, plus flexible pipe and hose
  • Max working pressure: 16 bar (1,600 kPa, 235 psi) at 20°C — PN16 rated
  • Max temperature: 60°C (140°F) — cold water use
  • Drinking water: Easy Fit Poly range tested to AS/NZS 4020:2018
  • Made in: New Zealand (Hansen Products, Whangarei)

Key Features & Benefits

  • Fast & Easy to Assemble: Push the pipe onto the fitting and wind on the nut. No specialist site equipment or skilled labour required
  • Double Strength Grip: The nut and barbs give a superior double strength grip. When fitted correctly the fitting will not leak or blow off the pipe
  • One Piece Fitting: No components to lose, rust or corrode. Captive nut
  • No O-Ring, No Crimping, No Solvent Cement
  • Glass Fibre Reinforced Nylon: UV stabilised, giving weather, termite, fungi and bacterial resistance
  • Drinking Water: Material approved for use with potable (drinkable) water
  • High Flow: Hansen's fittings demonstrate excellent hydraulic flow characteristics
  • Above or Below Ground: Suitable for use above or below ground in varying operating pressures and temperatures
  • Strong, Lightweight & Compact
  • Trusted by Kiwi Farmers: Hansen says its Easy Fit poly fittings have been trusted by Kiwi farmers for over 50 years
  • Hansen Limited Lifetime Warranty: All Hansen manufactured products carry Hansen's Limited Lifetime Warranty (conditions apply)
  • New Zealand Made

Choosing Your Female Threaded Tee

Thread in the middle, poly on the run

The HFT is a tee with a female BSPT (tapered) thread on the middle (branch) outlet and Easy Fit poly ends, each with a Poly Nut, on both run ends. All three are the same size: for example the HFT25 has a 1" female thread in the middle and 25mm poly on both run ends. Hansen's sizes are: 15mm = 1/2", 20mm = 3/4", 25mm = 1", 32mm = 1 1/4", 40mm = 1 1/2", 50mm = 2".

Need a different fitting?

Delivery or Collection

Stock Sizes 15mm–50mm are stocked in store. We hold limited stock of other sizes, and can order them in if needed.
Delivery Courier nationwide. Shipping is calculated at checkout based on your location.
Collections Available from 21 Akatea Road, Glendene, Auckland.

Materials & Standards

Material

Body & nuts: high quality glass fibre reinforced nylon, UV stabilised. The AS/NZS 4020 test report lists the compound as Polyamide 6 Glass Fibre Reinforced (Durethan BKV 15F).

AS/NZS 4020:2018 — Products in Contact with Drinking Water

Hansen Easy Fit Poly Fittings from 15mm to 50mm have met the requirements of AS/NZS 4020:2018. The EasyFit and TrueFit range was tested at the Australian Water Quality Centre (report 356792, completed 7 March 2023).

Fire Rating

Hansen lists the Easy Fit Poly range as fire rated UL94HB.

Pressure Rating

Fitting Sizes Max @ 20°C kPa psi
15mm – 50mm (HFT) 16 bar 1,600 kPa 235 psi

Hansen rates Easy Fit Poly fittings PN16, a maximum working pressure of 16 bar at 20°C (68°F). Hansen tests its products for cold water use up to 60°C (140°F) and does not recommend use above that. Your pipe's own pressure rating may be lower, so check the pipe table below.

Installation in Brief

  • Seal the thread: Use either a thread sealing paste or tape on all threaded connections. Hansen recommends Loctite 5331. Use a non-hardening sealant that is compatible with plastic
  • Cut square: Cut the pipe with pipe cutters, a knife or saw. Ensure a square cut of pipe ends and clean burrs off the pipe
  • Push on: Ensure the nut is fully wound back onto the body of the fitting. Push the pipe onto the fitting and as far as possible into the nut
  • Wind on & tighten: Wind the nut onto the pipe by hand as tight as possible, then tighten with a spanner or pipe grips until the nut is firm on the pipe
  • Support your pipework: All pipe work must be adequately supported
  • Follow the standards: Install as per the applicable standards and approvals for pipe and fittings, and follow the pipe manufacturer's guidelines

Full step-by-step guide, tightening and leak troubleshooting: Hansen poly fittings installation guide (Easy Fit Poly).

Hansen Easy Fit poly fittings 3-step installation: cut pipe square, push pipe onto fitting, wind on and tighten nut

Hansen's Threaded Fitting Handy Tips: how to apply thread tape and tighten a threaded joint without over-tightening.

Full Size Table — All 6 Hansen Female Threaded Tees (HFT)

Hansen Code Middle Thread Run Ends Spare Nut
HFT15 Female BSPT 1/2" (15mm) Poly 15mm (1/2") 15mm Poly Nut
HFT20 Female BSPT 3/4" (20mm) Poly 20mm (3/4") 20mm Poly Nut
HFT25 Female BSPT 1" (25mm) Poly 25mm (1") 25mm Poly Nut
HFT32 Female BSPT 1 1/4" (32mm) Poly 32mm (1 1/4") 32mm Poly Nut
HFT40 Female BSPT 1 1/2" (40mm) Poly 40mm (1 1/2") 40mm Poly Nut
HFT50 Female BSPT 2" (50mm) Poly 50mm (2") 50mm Poly Nut

Middle Thread is the branch outlet (female BSPT, no nut). Run Ends are the two Easy Fit poly ends, each with a Poly Nut. Sizes and codes are from Hansen's catalogue (BSPT thread size x pipe size x pipe size); spare nuts are from Hansen's product pages. All are rated 16 bar at 20°C. Choose the code from the Size drop-down above. Hansen's website and catalogue don't publish dimension drawings for the HFT.

Pipe the HFT Fits — LDPE to NZS 7601:1978

Hansen's Easy Fit Poly pipe specification: standard NZS 7601:1978 (New Zealand) polyethylene pipe (Type 3) for cold water service. Dimensions are in mm.

Nominal Bore Inside Diameter Outside Diameter Wall Thickness Pipe Working Pressure
15 11.7–12.7 16.9–17.3 2.3–2.6 0.90 MPa (130.50 psi)
20 17.9–19.2 24.9–25.4 3.1–3.5 0.80 MPa (116.00 psi)
25 24.2–25.6 31.2–31.8 3.1–3.5 0.65 MPa (94.25 psi)
32 30.5–31.9 37.5–38.1 3.1–3.5 0.50 MPa (72.50 psi)
40 36.8–38.3 43.8–44.5 3.1–3.5 0.45 MPa (65.25 psi)
50 49.5–51.0 56.5–57.2 3.1–3.5 0.35 MPa (50.75 psi)

Hansen Easy Fit Poly fittings are designed for all sizes of New Zealand LDPE, EnduroFlex, Australian Rural (Class B) and Irish imperial pipe (including washdown hose and non toxic tube). They also suit other flexible pipe and hose, such as thin wall irrigation tubing and rubber hoses.

Chemical Compatibility

Using your tees with anything other than water? Check Hansen's Easy Fit Poly chemical resistance ratings before you install. Bleach, halogens such as chlorine, strong acids and oxidising agents are rated "Bad", and pool and spa use is not covered by Hansen's warranty.

View Chemical Compatibility Chart

Installation Guide

Step-by-step Easy Fit Poly installation, a tightening guide, do's and don'ts and leak troubleshooting, straight from Hansen's instructions.

View Installation Guide

Frequently Asked Questions

What is a Hansen female threaded tee used for?

Hansen says the HFT is used for connecting low density poly pipe (LDPE) and EnduroFlex to male threads, and can also be used to connect flexible pipe and hose.

Is the middle outlet a thread or a poly nut?

The middle (branch) outlet is a female BSPT thread with no nut; a male thread screws into it. The two run ends are Easy Fit poly ends, each with a Poly Nut, for the poly pipe.

What thread does it have?

A female BSPT (tapered) thread on the middle outlet, the same size as the poly run ends, per Hansen's catalogue.

Do I need thread tape or sealant?

Yes. Hansen says to use either a thread sealing paste or tape on all threaded connections, and recommends Loctite 5331. The right sealant is non-hardening and compatible with plastic. Don't over-tighten the thread.

How tight should I tighten my fittings?

Hansen says to wind the nut by hand onto the pipe as tight as possible, then use a spanner or pipe grips to tighten until the nut is firm on the pipe.

What type of pipe will Hansen Easy Fit poly fittings connect to?

New Zealand LDPE (low density polyethylene pipe), EnduroFlex, Australian Rural Class B, and Irish imperial polythene pipes, including washdown hose and non toxic tube.

Will a Hansen female threaded tee fit medium density (MDPE) pipe?

Hansen designs Easy Fit Poly fittings for low density pipe. For medium density polyethylene pipe, Hansen makes its Easy Fit MD compression fittings, such as the MD Female Threaded Tee (HMDFT).

Is a Hansen female threaded tee safe for drinking water?

Yes. Hansen Easy Fit Poly fittings are made from a material approved for use with potable (drinkable) water, and fittings from 15mm to 50mm have met the requirements of AS/NZS 4020:2018 (Australian Water Quality Centre report 356792).

What pressure is a Hansen female threaded tee rated to?

Hansen rates Easy Fit Poly fittings PN16, a maximum working pressure of 16 bar (1,600 kPa, 235 psi) at 20°C. Your pipe may have a lower rating; for example, Hansen's NZS 7601 LDPE table shows 0.90 MPa for 15mm pipe down to 0.35 MPa for 50mm.

What temperature can I use Hansen Easy Fit poly fittings at?

Hansen tests all its products for cold water use up to a maximum of 60°C (140°F) and does not recommend use above that, as plastic expands as temperature rises. Products that fail above 60°C are not covered by Hansen's Limited Lifetime Warranty.

Can I use Hansen Easy Fit fittings under driveways, paths and foundations?

No. Hansen does not recommend the use of any Hansen Easy Fit fittings under any driveways, paths or foundations.

Can I use Hansen Easy Fit poly fittings in marine applications?

Yes. Hansen says Easy Fit Poly fittings are resistant to sea water, will not leach any substances harmful to marine life, and have provided excellent service in marine applications for many years.

Can I use my Hansen fittings with my swimming pool or spa?

No. Hansen says the high concentration of chlorine used in pool water will attack the material. The fitting material is only suitable for domestic water, and pool or spa use is not covered by Hansen's Limited Lifetime Warranty.

Can I get a spare nut?

Yes. The nuts are on the two poly run ends; the middle thread has no nut. Hansen lists a spare Poly Nut matching the size, for example the 25mm Poly Nut for the HFT25.