BWT-HKIT25S
$120.00 NZD
All prices include GST
Big Water Tanks Hose Kits connect your water tank to your pump with Hansen poly fittings, a Hansen ball valve and flexible black suction hose. Choose the 25mm Single Tank kit, or the 32mm Double Tank kit to link two tanks together and feed your pump.
Big Water Tanks Hose Kit available as a single 25mm kit or 32mm balancing connection kit. Both use heavy-duty Hansen poly fittings, Hansen ball valves and flexible suction hose to connect your tank to the pump inlet. These are the same kits included in our 30,000L Water Tank Combo and 2 x 30,000L Water Tanks Combo.
| 25mm Single Tank | 32mm Double Tank | |
|---|---|---|
| SKU | BWT-HKIT25S | BWT-HKIT32D25 |
| Use | Connect one tank to your pump | Link two tanks together and feed your pump |
| Tank fitting | 1 x 50mm - 25mm reducing hex nipple | 2 x 50mm - 32mm reducing hex nipples |
| Ball valves | 1 x 25mm | 2 x 32mm |
| Elbows | 1 x 25mm male elbow coupling | 2 x 32mm male elbow couplings |
| Tee | - | 1 x Hansen tee coupling (HT32) |
| Suction hose | 2m, 25mm | 6m, 32mm |
| Pump end | 25mm male coupling (hose to BSP) | 32mm female coupling (hose to BSP) and 32mm - 25mm reducing hex nipple |
On the 32mm Double Tank kit, the isolation valves let you isolate individual tanks for maintenance if needed.
Hansen ball valves carry a lifetime warranty (see the Hansen Ball Valves page).
25mm Single Tank (BWT-HKIT25S):

32mm Double Tank (BWT-HKIT32D25):

1Seal every thread
Use PTFE thread tape, or a non-hardening thread sealant that is compatible with plastic (Hansen recommends Loctite 5331), on all threaded connections.
2Hand tight + 1 to 2 turns
Tighten threaded fittings until firm with a spanner on the hex, no more. Do not over-tighten.
3Cut the hose square
Cut the suction hose with pipe cutters, a knife or saw. Ensure a square cut and clean burrs off the end.
4Push on
Make sure the nut is fully wound back onto the body of the fitting, then push the hose onto the fitting and as far as possible into the nut.
5Wind on and tighten
Wind the nut onto the hose by hand as tight as possible, then tighten with a spanner or pipe grips until the nut is firm.
6Support your pipework
All pipe work must be adequately supported.
Hansen's Threaded Fitting Handy Tips: how to apply thread tape and tighten True Fit fittings.
Steps from our Hansen Reducing Hex Nipple and Male Bend pages, which follow Hansen's installation guides.
| Code | Part | 25mm Single | 32mm Double |
|---|---|---|---|
| HRHN5025 / HRHN5032 | Reducing Hex Nipple 50mm (BSP) | 1 x 50 - 25mm | 2 x 50 - 32mm |
| HBV25 / HBV32 | Frost Resilient Ball Valve | 1 x 25mm | 2 x 32mm |
| HMBS25 / HMBS32 | Male Elbow Coupling (BSP to HOSE) | 1 x 25mm | 2 x 32mm |
| HT32 | Tee Coupling | - | 1 |
| HOS-BL25 / HOS-BL32 | Black Suction Hose | 2m, 25mm | 6m, 32mm |
| HMS25 | Male Coupling (HOSE to BSP) | 1 x 25mm | - |
| HFS32 | Female Coupling (HOSE to BSP) | - | 1 x 32mm |
| HRHN3225 | Reducing Hex Nipple 32mm - 25mm (BSP) | - | 1 |
| Pump end | 25mm male thread (suits most 25mm female pump inlets) | 25mm male (HMS25) | 25mm male (HFS32 + HRHN3225) |
Technical documents are published by Hansen Products (NZ) Ltd.
The 25mm Single Tank kit connects one tank to your pump. The 32mm Double Tank kit links two tanks together and feeds your pump.
It connects the bottom 50mm outlets of both tanks together with a flexible suction line and isolation valves. Water levels equalise naturally between both tanks, and you can isolate individual tanks for maintenance if needed.
Both kits start with a Hansen reducing hex nipple from 50mm (BSP): 50mm - 25mm on the single kit and 50mm - 32mm on the double kit.
Both kits finish at a 25mm male thread, which suits most pump inlets (25mm female). The double kit gets there with the HRHN3225 32mm - 25mm reducing hex nipple. The kits suit almost all of our water pumps; the DAB Esybox Pop is the only one that uses different fittings, so these kits don't suit it directly.
No. Thread tape is required to connect threaded fittings. Hansen also recommends Loctite 5331 as a non-hardening sealant that is compatible with plastic.
Hansen ball valves meet AS/NZS 4020, the Australian and New Zealand drinking water test standard.
Great fit, suitable for our system!