Search

HAN-HMDRBE2515

Hansen - MDPE Reducing Bracket Elbow - HMDRBE

Side A
Side B - BSPT

How to choose your size

  • Side A: the MDPE pipe size (mm), the compression end.
  • Side B - BSPT: the female thread size (for the tap).
  • Example: 25mm pipe x ¾" thread = Side A 25mm, Side B - BSPT ¾" (HMDRBE2520).

Combinations that aren't made are greyed out.

Big Water Tanks is an official stockist of Hansen Products — New Zealand-made pipe fittings for farm, irrigation, rural water and plumbing. The Hansen Easy Fit MD Compression Reducing Bracket Elbow (HMDRBE) connects a tap to medium density polyethylene (MDPE) pipe. 3 sizes: 20mm x ½", 25mm x ½", 25mm x ¾".

Hansen Easy Fit MD Compression Reducing Bracket Elbow (HMDRBE): MDPE Pipe × Female BSPT Thread

One end is a compression end for MDPE pipe; the other is a female BSPT (British Standard Pipe Taper) thread at 90° for the tap, on a bracket base so the elbow can be fixed in place. The compression end has a nut, grip ring, thrust ring, O-ring and seal: undo the nut to the last thread, push the pipe through the nut, white grip ring and thrust ring and past the seal to the stop, then tighten the nut. The threaded end has no nut or grip ring. Hansen describes the HMDRBE as "Used for connecting taps to Medium Density Pipe using a compression style joint. Pipe Size x BSPT Thread Size." In the code, the first number is the pipe size in mm and the second is the thread size: HMDRBE2520 is 25mm pipe x ¾" thread. Hansen's codes use the mm equivalent of each thread size: 15 = ½", 20 = ¾", 25 = 1", 32 = 1¼", 40 = 1½", 50 = 2", 63 = 2½", 75 = 3", 100 = 4". Hansen makes these fittings in New Zealand from UV stabilised polypropylene, and the Easy Fit Compression range carries WaterMark certification and is tested to AS/NZS 4020:2018 for contact with drinking water.

Quick Facts

  • Connection: MDPE pipe compression end × female BSPT thread at 90°. The compression end has a nut, grip ring, thrust ring, O-ring and seal
  • Thread end: Female BSPT (British Standard Pipe Taper), ½", ¾"
  • Pipe sizes: 20, 25mm MDPE
  • Sizes: 3 sizes: 20mm x ½", 25mm x ½", 25mm x ¾". In the code, the first number is the pipe (mm), the second the thread
  • Fits: Medium density polyethylene pipe (PE80 and PE100) to AS/NZS 4130, sized by outside diameter
  • Max working pressure: 16 bar (1,600 kPa, 235 psi) for 20mm to 25mm, at 20°C (by pipe size)
  • Materials: Polypropylene body and nuts, acetal grip ring, polypropylene thrust ring, nitrile rubber O-ring and seal
  • Approvals: WaterMark WMKA21978 (AS/NZS 4129:2020), AS/NZS 4020:2018 drinking water, WRAS
  • Made in: New Zealand (Hansen Products, Whangarei)

Key Features & Benefits

  • Made in New Zealand: Manufactured using the best quality materials to withstand the harshest weather conditions
  • Largest MD Range Made in NZ: Hansen says it is the largest medium density fitting range made in New Zealand
  • One Piece Fitting: Captive components when the fitting is assembled correctly
  • Pre-lubricated Seal: For easy pipe insertion and reliable leak free connections
  • UV Stabilised: Weather, termite, fungi and bacterial resistance
  • High Pressure Rated: 16 bar up to 63mm, 12.5 bar from 75mm to 110mm
  • Sleek, Compact Design: For easy installation
  • Easy Grip Nuts: For rapid winding onto the pipe
  • Dependable Threads: High quality threaded components
  • Drinking Water Approved: Potable (drinkable) water approved
  • Hansen Limited Lifetime Warranty: All Hansen manufactured products carry Hansen's Limited Lifetime Warranty (conditions apply)
  • Trusted for Over 50 Years: Hansen has been making pipe fittings in New Zealand for over 50 years

Choosing Your MD Reducing Bracket Elbow

Which end is which?

One end is a compression end for MDPE pipe; the other is a female BSPT (British Standard Pipe Taper) thread at 90° for the tap, on a bracket base so the elbow can be fixed in place. Pick Side A for the MDPE pipe and Side B - BSPT for the thread.

How to order

Choose Side A (pipe size) and Side B - BSPT (thread size) above. For example, 25mm pipe and a ¾" thread is the HMDRBE2520. Combinations Hansen doesn't make are greyed out.

Measure the pipe and the thread

MDPE is sized by its outside diameter, so a 32mm fitting suits pipe with a 32mm outside diameter; check the pipe table below. Match the thread to the nominal BSPT size of the male thread you are connecting to. Hansen's codes use the mm equivalent of each thread size: 15 = ½", 20 = ¾", 25 = 1", 32 = 1¼", 40 = 1½", 50 = 2", 63 = 2½", 75 = 3", 100 = 4".

Need a different fitting?

Delivery or Collection

Stock Sizes up to 50mm are stocked in store. We hold limited stock of larger sizes, and can order them in if needed.
Delivery Courier nationwide. Shipping is calculated at checkout based on your location.
Collections Available from 21 Akatea Road, Glendene, Auckland.

Materials & Standards

Easy Fit Compression Fittings Materials

Part Material
Body & Nuts High quality polypropylene (virgin PP)
Grip Ring High quality acetal (virgin POM)
Thrust Ring High quality polypropylene (PP)
O-Ring High quality nitrile rubber (NBR)
Seal High quality nitrile rubber (NBR)

UV stabilised. Materials are from Hansen's Easy Fit Compression Fittings materials list.

WaterMark — AS/NZS 4129:2020

WaterMark Certificate of Conformity (Level 1), evaluated to AS/NZS 4129:2020 — Fittings for polyethylene (PE) pipes for pressure applications. Certificate No. WMKA21978, issued by SAI Global, current to 29 July 2028. Hansen's Easy Fit MD Compression range, including the HMDRBE, is covered by this certificate.

AS/NZS 4020:2018 — Products in Contact with Drinking Water

Hansen Easy Fit Compression Fittings (MD) were tested to AS/NZS 4020:2018 by the Australian Water Quality Centre (report 369234, completed 31 August 2023).

WRAS

WRAS product approval 240504011 for the Hansen Easy Fit range of polypropylene compression fittings, valid to May 2029.

Pressure Rating

Fitting Sizes Max @ 20°C kPa psi
20mm – 25mm 16 bar 1,600 kPa 235 psi

Hansen's maximum working pressures at 20°C (68°F), by MDPE pipe size. Your pipe's own pressure class may be lower, so check the pipe table below.

Installation in Brief

Reliable leak-proof seals are the hallmark of Hansen fittings, and the Easy Fit Compression range installs in four simple steps:

Hansen Easy Fit MD compression install step 1: cutting MDPE pipe square with pipe cutters

1Cut and chamfer

Cut the pipe square with pipe cutters, a knife or saw, and chamfer the pipe end. Clean off any burrs and keep the pipe end clean and as free of scratches as possible.

Hansen Easy Fit MD compression install step 2: nut undone to the last thread

2Undo the nut

Undo the nut to the last thread. Don't remove the nut from the body.

Hansen Easy Fit MD compression install step 3: pipe pushed past the seal to the stop point, showing grip ring and thrust ring

3Push the pipe in

Push the pipe through the nut, white grip ring and thrust ring until it meets the seal, then push firmly past the seal all the way to the stop point.

Hansen Easy Fit MD compression install step 4: hand tightening the nut

4Tighten

Firmly hand tighten the nut. On 40mm and greater, use a pair of Poly Grips for a further half turn past hand tight.

Note: The hydraulic seal is made when the pipe passes the seal; tightening the nut gives pull-out resistance.

Hansen's product page FAQ also says: "Up to 32mm just tighten hand tight and all sizes above use a spanner to tighten another ½ to 1 turns past hand tight."

Chamfering the pipe end makes it easier to push past the seal. We stock the Hansen Chamfering Tool (HMDCHAMF).

The threaded end

The female BSPT thread is not a compression end: there is no nut or grip ring on it. Seal the thread with a thread sealing paste or tape. Hansen recommends Loctite 5331; use a non-hardening sealant that is compatible with plastic, and use it on the thread only, never on the MDPE pipe or inside the compression end. Screw the male thread into it by hand, then tighten firmly without over-tightening. Fit the threaded end first where you can, then connect the MDPE pipe.

Installation standards

Hansen says Easy Fit Compression fittings should be installed onto medium density pipe that has been installed in accordance with:

  • AS/NZS 2566 Part 1 and Supplement "Buried Flexible Pipelines — Structural Design" (detailed installation and site pressure testing)
  • AS/NZS 2566 Part 2 "Installation"
  • AS/NZS 2033 Installation of Polyethylene Pipe Systems

Not following these standards may void any warranties given by Hansen Products (NZ) Limited for the fitting. Follow the pipe manufacturer's guidelines.

Hansen's MD Compression Fitting Handy Tips: handy tips for installing Easy Fit Compression fittings on MDPE pipe.

Full Size Table — All 3 Hansen MD Reducing Bracket Elbows

Hansen Code Pipe x Thread Max @ 20°C Spare Parts
20mm Pipe
HMDRBE2015 20mm x ½" 16 bar 20mm spares
25mm Pipe
HMDRBE2515 25mm x ½" 16 bar 25mm spares
HMDRBE2520 25mm x ¾" 16 bar 25mm spares

Codes and sizes are from Hansen's catalogue; pressures are Hansen's at 20°C, by pipe size. Threads are BSPT. The Spare Parts column links to the matching pipe size of our Hansen Compression Spare Parts; choose the thrust ring, nut, grip ring or O-ring there. Spares are for the compression end; the threaded end has no nut or grip ring. Big Water Tanks sells all the spare parts.

Pipe the HMDRBE Fit — PE Pipe to AS/NZS 4130:2018

Hansen's Easy Fit Compression pipe specification: AS/NZS 4130:2018 polyethylene pipes for pressure applications. Mean outside diameter and wall thickness (min–max) in mm, by pressure class.

Nominal OD Mean OD PN6.3 Wall PN9 Wall PN12.5 Wall PN16 Wall
20 20.0–20.3 1.6–1.9* 1.6–1.9* 1.9–2.2 1.9–2.2
25 25.0–25.3 1.6–1.9* 1.6–1.9* 2.3–2.7 2.3–2.7
32 32.0–32.3 1.6–1.9 1.9–2.2* 2.9–3.3 2.9–3.3
40 40.0–40.4 1.9–2.2 2.4–2.8* 3.7–4.2 3.7–4.2
50 50.0–50.5 2.4–2.8 3.0–3.4* 4.6–5.2 4.6–5.2
63 63.0–63.6 3.0–3.4 3.8–4.3* 5.8–6.5 5.8–6.5
75 75.0–75.7 3.6–4.1 4.5–5.1* 6.8–7.6 6.8–7.6
90 90.0–90.9 4.3–4.9 5.4–6.1* 8.2–9.2 8.2–9.2
110 110.0–111.0 5.3–6.0 6.6–7.4* 10.0–11.1 10.0–11.1

PN6.3, PN9 and PN12.5 are PE80; PN16 is PE100. Pipe working pressures: PN6.3 0.63 MPa (91.4 psi), PN9 0.90 MPa (130.5 psi), PN12.5 1.25 MPa (181.3 psi), PN16 1.60 MPa (232.1 psi). *Hansen notes these wall thicknesses are not included in AS/NZS 4130:2018 and are based on industry documentation.

Chemical Compatibility

Using your bracket elbows with anything other than water? Hansen's Easy Fit Compression chemical resistance chart rates the polypropylene, acetal and nitrile rubber parts separately. Check it before you install.

View MD Compression Chemical Chart

Installation Guide

Hansen's Easy Fit MD Compression cheat sheet covers cutting, chamfering, inserting the pipe and tightening, with the installation standards to follow.

Download MD Installation Sheet (PDF)

Frequently Asked Questions

What is the Hansen HMDRBE used for?

Hansen says: "Used for connecting taps to Medium Density Pipe using a compression style joint. Pipe Size x BSPT Thread Size." Connects a tap to medium density polyethylene (MDPE) pipe.

Which end is the thread and which is the compression end?

One end is a compression end for MDPE pipe; the other is a female BSPT (British Standard Pipe Taper) thread at 90° for the tap, on a bracket base so the elbow can be fixed in place. Side A is the pipe size and Side B - BSPT is the thread size.

What thread is it?

BSPT (British Standard Pipe Taper), as listed by Hansen. The HMDRBE has a female thread. Hansen's codes use the mm equivalent of each thread size: 15 = ½", 20 = ¾", 25 = 1", 32 = 1¼", 40 = 1½", 50 = 2", 63 = 2½", 75 = 3", 100 = 4".

How do I read the HMDRBE code?

The first number is the MDPE pipe size in mm and the second is the thread size in Hansen's mm equivalent. HMDRBE2520 = 25mm pipe x ¾" thread.

What should I seal the thread with?

Use a thread sealing paste or tape on the threaded end. Hansen recommends Loctite 5331; use a non-hardening sealant that is compatible with plastic. Use it on the thread only: the compression end seals with its own O-ring and seal, so don't put sealant on the MDPE pipe.

Will these fit my low density (LDPE) poly pipe?

No. Hansen designs its Easy Fit Compression fittings for medium density polyethylene pipe, sized by outside diameter. For low density poly pipe use Hansen Easy Fit Poly fittings.

How tight should I tighten my Easy Fit MD compression fittings?

Hansen gives two lines of guidance. Its product page FAQ says: "Up to 32mm just tighten hand tight and all sizes above use a spanner to tighten another ½ to 1 turns past hand tight." Its installation sheet says: "Firmly hand tighten the Nut. Use a pair of Poly Grips for a further half turn past hand tight for final tightening on 40mm fittings and greater." Hansen adds that you already have a seal once the pipe is past the O-ring; the nut only compresses the grip ring to hold the pipe in place.

Do I need to chamfer the pipe?

Yes. Hansen's installation steps say to cut the pipe square, chamfer the end and clean off burrs. We stock the Hansen Chamfering Tool (HMDCHAMF).

Can I use MD fittings in my house water supply?

Yes. Hansen says its Easy Fit MD Compression fittings are potable (drinking) water approved. They have been tested to AS/NZS 4020:2018 (AWQC report 369234) and carry WaterMark certification WMKA21978.

What pressure are they rated to?

Hansen rates 20mm to 25mm at 16 bar (1,600 kPa, 235 psi), at 20°C. Your pipe's pressure class may be lower.

Can I get spare parts?

Yes, for the compression end. Hansen lists a thrust ring, grip ring, nut and O-ring for each pipe size, and Big Water Tanks sells all the spare parts: order them from our Hansen Compression Spare Parts page by part and size.

Can I use Hansen Easy Fit fittings under driveways, paths and foundations?

No. Hansen does not recommend the use of any Hansen Easy Fit fittings under any driveways, paths or foundations.

Does this fitting carry Hansen's Limited Lifetime Warranty?

Yes. All Hansen manufactured products carry Hansen's Limited Lifetime Warranty (conditions apply). Hansen says installing outside the listed pipe installation standards may void its warranty.