Search

BMT-DDIV202

Quickfit Downpipe Diverter Round 80mm/90mm/100mm - Rain Barrel Diverter

Big Water Tanks stocks the Rain Harvesting Quickfit Diverter Round, NZ model DDIV202 for 80mm, 90mm and 100mm round downpipe. Drill a 35mm hole, push the rubber collector into your downpipe, screw the diverter on and run a hose to your rain barrel. No glue, no cutting out pipe.

Recommended for tanks of 2000L and under. For larger tanks, we recommend sending all the water into the tank and letting the overflow handle the excess.

Quickfit Diverter Round: Drill-In Rain Barrel Diverter for 80mm to 100mm NZ Downpipe

Recommended for tanks of 2000L and under

A downpipe diverter only takes part of the flow from your downpipe (up to 180 L/hour with a 12mm garden hose, or 750 L/hour with the 32mm hose, per Rain Harvesting). That suits a rain barrel or a small tank of up to 2000 litres.

For larger tanks, Big Water Tanks recommends sending all the water from your downpipes into the tank and letting the tank's overflow handle the excess, so you capture every heavy downpour. See our larger water tanks or the Rain Harvesting range for rain heads and first flush diverters that go with a full-flow system. Not sure? ask us.

For tanks of 3000L and larger, we recommend our 100mm Overflow and Inlet Vent Kit on the tank inlet and overflow.

Rain Harvesting says: "The quickest way to start collecting water from your round downpipes. It's as simple as making a hole in your pipe and then pressing the diverter inside. Then just connect it to your barrel and you're done! No glue, no fuss."

Quick Facts

  • Type: In-pipe downpipe diverter with a rubber collector and On/Off dial
  • NZ model: DDIV202, pipe fitment 80 to 100mm round downpipe
  • Water capture: Up to 180 L/hour (40 gal/hr) with a 12mm (½") garden hose; up to 750 L/hour (190 gal/hr) with the 32mm (1¼") high flow hose
  • Hose fittings: 12mm (½") garden hose and 32mm (1¼") hose fittings included; 1" BSP nozzle
  • Installation: Drill a 35mm (1⅜") hole with the hole saw supplied, push in the collector and screw the diverter on
  • Best for: Rain barrels and tanks of 2000L and under
  • Made by: Rain Harvesting by Blue Mountain Co

Key Features & Benefits

  • Small yet effective: "It might be a small unit, but it gets the job done!" Up to 180 L/hour with a 12mm (½") garden hose, or up to 750 L/hour with the 32mm (1¼") high flow hose.
  • Quick installation: Drill a hole in your downpipe and push the rubber rainwater catcher into place. Add a Downpipe Diverter Hose Kit to connect it to your rain barrel.
  • On/Off switch: Stop collecting water when your rain barrel is full, or in winter, at the turn of a dial, then start again whenever you want.
  • Simple connections: Fittings for a ½" garden hose and the 1¼" high flow hose are included, so you can set the system up however you need.
  • Hole saw included: The 35mm (1⅜") hole saw for your downpipe comes in the box.

Maintenance

Rain Harvesting: "To keep your Quickfit Diverter performing at its best, ensure you install a rain head above the diverter to ensure that no leaves or debris can become lodged in your Quickfit Diverter."

To check it:

  1. Unscrew the diverter from your pipe, using only a medium torque so the screws don't strip out.
  2. Carefully remove the rubber collector from the pipe.
  3. Hose or brush out any debris, then refit your Quickfit Diverter.

For a rain head above it, see the Leaf Eater® Stream Original, a slim rain head that sits in your downpipe and keeps leaves and debris out (for 65mm, 80mm and 100mm NZ downpipe), and the rest of our Rain Harvesting range.

From Rain Harvesting's Quickfit Diverter Round Installation and Specification Guide.

What's in the Box

  • Quickfit Diverter valve
  • Quickfit Diverter round rubber collector
  • 12mm (½") garden hose fitting and seal
  • 32mm (1¼") hose fitting and seal
  • Screws x 2
  • Hole saw 35mm (1⅜")

Tools and materials you may need: tape measure, marker pen, drill, utility knife, spirit level and liquid soap.

The hose to your barrel is not included. For the 32mm high flow connection, add the Downpipe Diverter Hose Kit.

From Rain Harvesting's Quickfit Diverter Round Installation and Specification Guide.

Pair It with the Right Tank

The Quickfit Diverter Round is made for rain barrels and smaller tanks of 2000L and under. Connect it with the Downpipe Diverter Hose Kit, and join extra barrels with the Rain Barrel Linking Kit. For a bigger tank, we recommend running the whole downpipe into the tank with an overflow; see our larger water tanks and the rest of our Rain Harvesting range.

For higher capture (up to 1200 L/hour) on 65, 80 or 90mm pipe, see the Downpipe Diverter Round.

How It Works

The rubber collector sits inside your downpipe and catches water running down the pipe. It flows out through the diverter, past the On/Off dial and down the hose into your rain barrel.

How the Rain Harvesting Quickfit Diverter Round works, lettered A to E
  • AWater flow from roof
  • BOn/Off dial
  • CRain barrel
  • DHose
  • EInterchangeable hose fittings: a standard garden hose or high flow 32mm (1¼") hose

Labels from the diagram in Rain Harvesting's Quickfit Diverter Round Installation and Specification Guide.

Pipe Size: Collector Trim Guide

The rubber collector suits 100mm pipe as supplied. Trim its tips to suit smaller pipe before you push it in.

100mm pipe

Quickfit Diverter Round collector for 100mm downpipe, no trimming

No adjustments are necessary.

90mm pipe

Quickfit Diverter Round collector for 90mm downpipe, one tip cut off

Cut off one of the tips of the collector.

80mm pipe

Quickfit Diverter Round collector for 80mm downpipe, both tips cut off

Cut off both tips of the collector.

From Figure 1 in Rain Harvesting's Quickfit Diverter Round Installation and Specification Guide.

Installation in Brief

Rain Harvesting's steps, in brief. Download the full guide below before you drill.

1Mark the position

Point the outlet the way you will route the hose. For a rain barrel, mount the diverter level with the barrel inlet, just below the top of the barrel. Use a spirit level to check the height.

2Drill the hole

Use the included hole saw to drill a hole in your downpipe at the mark. Remove any burrs from the edge of the hole.

3Trim the collector

Trim the collector tips if needed for your pipe size (see the trim guide above).

4Insert the collector

Compress the rubber collector and push it through the hole, the right way up: there is an indicator on the front. Liquid soap makes it easier to insert.

5Fit the diverter

Press the Quickfit Diverter onto the rubber collector so the mounting holes line up, then screw it to the downpipe using only moderate torque so the screws do not strip out. This seals the diverter to the downpipe.

6Connect the hose

Screw the 12mm or 1¼" hose fitting onto the nozzle, connect the hose to your rain barrel or tank, and set the On/Off knob where you need it.

Steps condensed from Rain Harvesting's Quickfit Diverter Round Installation and Specification Guide.

Specifications

Code Pipe fitment A B C D E
DDIV202 80 to 100 76 96 102 64 1" BSP

All dimensions in mm, from Rain Harvesting's Quickfit Diverter Round Installation and Specification Guide.

Quickfit Diverter Round dimension drawing, lettered A to E
  • A76mm
  • B96mm
  • C102mm
  • D64mm
  • E1" BSP hose nozzle

Downloads

Installation Guide (PDF) Rain Harvesting: Quickfit Diverter Round

The installation guide is published by Rain Harvesting by Blue Mountain Co.

Videos

Round In-pipe Diverter Product Overview

How to maintain your Quickfit Diverter Round

Official videos from Rain Harvesting's YouTube channel.

Frequently Asked Questions

Is a downpipe diverter right for my tank?

We recommend it for rain barrels and tanks of 2000L and under. A diverter only takes part of the downpipe flow (up to 180 L/hour with a 12mm garden hose, or 750 L/hour with the 32mm hose). For larger tanks, Big Water Tanks recommends diverting all the water into the tank and letting the tank's overflow handle the excess. See our larger water tanks.

What size downpipe does it fit?

Round downpipe from 80mm to 100mm (NZ model DDIV202). Trim the collector tips for 90mm or 80mm pipe as shown in the trim guide.

Do I need to cut my downpipe?

No. You drill one 35mm (1⅜") hole with the hole saw supplied, push the collector in and screw the diverter on. No glue.

Which hose should I use?

A 12mm (½") garden hose collects up to 180 L/hour. The 32mm (1¼") high flow hose collects up to 750 L/hour; the Downpipe Diverter Hose Kit has the hose, clamps, barrel outlet and hole saw.

Do I need a rain head?

Rain Harvesting recommends a rain head above the diverter so leaves and debris do not lodge in it. See the Leaf Eater® Stream Original, a slim rain head that sits in your downpipe (for 65mm, 80mm and 100mm NZ downpipe).

How do I clean it?

Unscrew the diverter (medium torque only), carefully remove the rubber collector, hose or brush out any debris, then refit it.

How is it different from the Downpipe Diverter Round?

The Quickfit fits through a hole in 80 to 100mm pipe and collects up to 750 L/hour. The Downpipe Diverter Round replaces a section of 65, 80 or 90mm downpipe, has a built-in leaf filter and collects up to 1200 L/hour.

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)