Search

HAN-HMDTR32

Hansen - MDPE Compression Spare Parts - Nut, Grip Ring, Thrust Ring & O-Ring

Item
Size

How to choose your spare part

  • Item: pick the part first: Nut, Grip Ring, Thrust Ring or O Ring.
  • Size: then pick the MDPE pipe size (mm) of the compression end it goes on.
  • Reducing fittings: each end takes spares in its own size. A 32mm x 25mm reducing coupling uses 32mm spares on the 32mm end and 25mm spares on the 25mm end.
  • Threaded fittings: spares are for the compression end only; the threaded end has no nut or grip ring.

Big Water Tanks is an official stockist of Hansen Products — New Zealand-made pipe fittings for farm, irrigation, rural water and plumbing. These are Hansen's replacement parts for its Easy Fit MD Compression fittings: the nut, grip ring, thrust ring and O-ring, in 9 sizes from 20mm to 110mm.

Hansen Easy Fit MD Compression Spare Parts: Nut, Grip Ring, Thrust Ring & O-Ring

Hansen describes these as "Replacement Parts for the Easy-Fit Compression fittings Range." Every compression end on an Easy Fit MD fitting is made up of the same parts. From the outside in: the nut, the white grip ring, the thrust ring, then the O-ring and seal inside the body. Hansen says you already have a seal once the pipe is past the O-ring; all the nut is doing is compressing the grip ring onto the pipe to hold the pipe in place. Each part is sold separately in the same size as the MDPE pipe, so you can replace a lost or damaged part without replacing the whole fitting. These parts are for medium density polyethylene (MDPE) pipe fittings sized by outside diameter, not for Hansen Easy Fit Poly fittings on low density (LDPE) poly pipe.

Quick Facts

  • Parts: Nut (HMDN), grip ring (HMDGR), thrust ring (HMDTR) and O-ring (HMDORING)
  • Sizes: 20, 25, 32, 40, 50, 63, 75, 90 and 110mm, by MDPE pipe size
  • Fits: Hansen Easy Fit MD Compression fittings, on MDPE pipe (PE80 and PE100) to AS/NZS 4130
  • Fitting order: Nut, grip ring, thrust ring, then O-ring and seal
  • Materials: Polypropylene nut, acetal grip ring, polypropylene thrust ring, nitrile rubber O-ring
  • Max working pressure: 16 bar (1,600 kPa, 235 psi) for 20mm to 63mm; 12.5 bar (1,250 kPa, 182 psi) for 75mm to 110mm, at 20°C (by pipe size)
  • Approvals: WaterMark WMKA21978 (AS/NZS 4129:2020), AS/NZS 4020:2018 drinking water, WRAS
  • Made in: New Zealand (Hansen Products, Whangarei)

What Each Part Does

Part Hansen Code Material What it does
Nut HMDN Polypropylene (virgin PP) Gives the joint its grip: tightening the nut compresses the grip ring onto the pipe to hold it in place. Easy grip nuts for rapid winding onto the pipe.
Grip Ring HMDGR Acetal (virgin POM) The white ring that grips the pipe when the nut is tightened, holding the pipe in the fitting.
Thrust Ring HMDTR Polypropylene (PP) Sits between the grip ring and the O-ring.
O Ring HMDORING Nitrile rubber (NBR) Makes the seal. Hansen says you have a seal once the pipe is past the O-ring.

Materials are from Hansen's Easy Fit Compression Fittings materials list.

Choosing Your Spare Parts

Pick the part, then the pipe size

Choose the Item (Nut, Grip Ring, Thrust Ring or O Ring), then the Size. The size is the MDPE pipe size of the compression end the part goes on. MDPE is sized by its outside diameter, so a 32mm part suits a fitting on pipe with a 32mm outside diameter.

Reducing fittings need spares in each size

Each compression end takes spares in its own size. A reducing coupling or reducing tee uses spares in both sizes, for example 32mm spares on the 32mm end and 25mm spares on the 25mm end.

Threaded fittings

On male and female threaded fittings, the spares are for the compression end only. The threaded end has no nut, grip ring, thrust ring or O-ring.

Which fittings they fit

These spares fit Hansen's Easy Fit MD Compression range:

Low density poly pipe (LDPE)? These parts don't fit Hansen Easy Fit Poly fittings; see Hansen Easy Fit Poly fittings.

When to Replace a Part

  • Lost or damaged: replace any part that is missing, cracked or split.
  • O-ring: replace it if it is cut, twisted, flattened or perished. The O-ring makes the seal, so a joint that weeps at the pipe after it has been assembled correctly usually needs a new O-ring. First check the pipe is cut square, chamfered, clean and pushed past the seal.
  • Grip ring: replace it if it is cracked or the pipe slips out after the nut has been tightened.
  • Re-using a fitting: when you take a fitting off the pipe to re-use it, check the grip ring and O-ring and replace any that are damaged.

Use spares in the same size as the fitting end. Ask us if you're not sure which part you need.

Delivery or Collection

Stock Sizes up to 50mm are stocked in store. We hold limited stock of larger sizes, and can order them in if needed.
Delivery Courier nationwide. Shipping is calculated at checkout based on your location.
Collections Available from 21 Akatea Road, Glendene, Auckland.

Materials & Standards

Easy Fit Compression Fittings Materials

Part Material
Body & Nuts High quality polypropylene (virgin PP)
Grip Ring High quality acetal (virgin POM)
Thrust Ring High quality polypropylene (PP)
O-Ring High quality nitrile rubber (NBR)
Seal High quality nitrile rubber (NBR)

UV stabilised. Materials are from Hansen's Easy Fit Compression Fittings materials list.

WaterMark — AS/NZS 4129:2020

WaterMark Certificate of Conformity (Level 1), evaluated to AS/NZS 4129:2020 — Fittings for polyethylene (PE) pipes for pressure applications. Certificate No. WMKA21978, issued by SAI Global, current to 29 July 2028. Hansen's Easy Fit MD Compression range is covered by this certificate; these are Hansen's replacement parts for that range.

AS/NZS 4020:2018 — Products in Contact with Drinking Water

Hansen Easy Fit Compression Fittings (MD) were tested to AS/NZS 4020:2018 by the Australian Water Quality Centre (report 369234, completed 31 August 2023).

WRAS

WRAS product approval 240504011 for the Hansen Easy Fit range of polypropylene compression fittings, valid to May 2029.

Pressure Rating

Fitting Sizes Max @ 20°C kPa psi
20mm – 63mm 16 bar 1,600 kPa 235 psi
75mm – 110mm 12.5 bar 1,250 kPa 182 psi

Hansen's maximum working pressures at 20°C (68°F), by MDPE pipe size. Your pipe's own pressure class may be lower.

Fitting Order

Each compression end goes together in this order, from the outside of the fitting in:

  1. Nut: threads onto the fitting body.
  2. Grip Ring: the white ring, inside the nut.
  3. Thrust Ring: behind the grip ring.
  4. O-ring and seal: inside the body, where the seal is made.

When you install, the pipe goes through the nut, white grip ring and thrust ring until it meets the seal, then past it. Hansen's step 3 image below shows each part in place.

Installation in Brief

Reliable leak-proof seals are the hallmark of Hansen fittings, and the Easy Fit Compression range installs in four simple steps:

Hansen Easy Fit MD compression install step 1: cutting MDPE pipe square with pipe cutters

1Cut and chamfer

Cut the pipe square with pipe cutters, a knife or saw, and chamfer the pipe end. Clean off any burrs and keep the pipe end clean and as free of scratches as possible.

Hansen Easy Fit MD compression install step 2: nut undone to the last thread

2Undo the nut

Undo the nut to the last thread. Don't remove the nut from the body.

Hansen Easy Fit MD compression install step 3: pipe pushed past the seal to the stop point, showing grip ring and thrust ring

3Push the pipe in

Push the pipe through the nut, white grip ring and thrust ring until it meets the seal, then push firmly past the seal all the way to the stop point.

Hansen Easy Fit MD compression install step 4: hand tightening the nut

4Tighten

Firmly hand tighten the nut. On 40mm and greater, use a pair of Poly Grips for a further half turn past hand tight.

Note: The hydraulic seal is made when the pipe passes the seal; tightening the nut gives pull-out resistance.

Hansen's product page FAQ also says: "Up to 32mm just tighten hand tight and all sizes above use a spanner to tighten another ½ to 1 turns past hand tight."

Chamfering the pipe end makes it easier to push past the seal. We stock the Hansen Chamfering Tool (HMDCHAMF).

Installation standards

Hansen says Easy Fit Compression fittings should be installed onto medium density pipe that has been installed in accordance with:

  • AS/NZS 2566 Part 1 and Supplement "Buried Flexible Pipelines — Structural Design" (detailed installation and site pressure testing)
  • AS/NZS 2566 Part 2 "Installation"
  • AS/NZS 2033 Installation of Polyethylene Pipe Systems

Not following these standards may void any warranties given by Hansen Products (NZ) Limited for the fitting. Follow the pipe manufacturer's guidelines.

Hansen's MD Compression Fitting Handy Tips: handy tips for installing Easy Fit Compression fittings on MDPE pipe.

Full Size Table — All 36 Hansen MD Spare Parts

Size Nut Grip Ring Thrust Ring O-Ring Fitting Max @ 20°C
20mm HMDN20 HMDGR20 HMDTR20 HMDORING20 16 bar
25mm HMDN25 HMDGR25 HMDTR25 HMDORING25 16 bar
32mm HMDN32 HMDGR32 HMDTR32 HMDORING32 16 bar
40mm HMDN40 HMDGR40 HMDTR40 HMDORING40 16 bar
50mm HMDN50 HMDGR50 HMDTR50 HMDORING50 16 bar
63mm HMDN63 HMDGR63 HMDTR63 HMDORING63 16 bar
75mm HMDN75 HMDGR75 HMDTR75 HMDORING75 12.5 bar
90mm HMDN90 HMDGR90 HMDTR90 HMDORING90 12.5 bar
110mm HMDN110 HMDGR110 HMDTR110 HMDORING110 12.5 bar

Codes and sizes are from Hansen's catalogue. Pressures are Hansen's maximum working pressures at 20°C for the fittings these parts go in. Tap a code to select that part.

Chemical Compatibility

Using your fittings with anything other than water? Hansen's Easy Fit Compression chemical resistance chart rates the polypropylene, acetal and nitrile rubber parts separately. Check it before you install.

View MD Compression Chemical Chart

Installation Guide

Hansen's Easy Fit MD Compression cheat sheet covers cutting, chamfering, inserting the pipe and tightening, with the installation standards to follow.

Download MD Installation Sheet (PDF)

Frequently Asked Questions

Which spare parts does Hansen make for Easy Fit MD fittings?

Hansen lists a nut (HMDN), grip ring (HMDGR), thrust ring (HMDTR) and O-ring (HMDORING) for each size, as "Replacement Parts for the Easy-Fit Compression fittings Range." We sell all four from 20mm to 110mm.

Which size do I need?

The size of the MDPE pipe on the end you're repairing. MDPE is sized by outside diameter, so a 32mm fitting on 32mm pipe takes 32mm spares.

I have a reducing fitting. Which size spares?

Each end takes spares in its own size. A 32mm x 25mm reducing coupling uses 32mm spares on the 32mm end and 25mm spares on the 25mm end. A reducing tee uses the run size for the two top ends and the branch size for the bottom.

Do threaded fittings take spare parts?

Only on the compression end. The threaded end of a male or female coupling, elbow, threaded tee or the reducing bracket elbow has no nut, grip ring, thrust ring or O-ring.

What order do the parts go in?

From the outside in: nut, grip ring, thrust ring, then the O-ring and seal inside the body.

Which part makes the seal?

The O-ring. Hansen says you already have a seal once the pipe is past the O-ring; all the nut is doing is compressing the grip ring onto the pipe to hold the pipe in place.

Will these fit Hansen Easy Fit Poly fittings?

No. These parts are for the Easy Fit MD Compression range on medium density pipe. For low density poly pipe use Hansen Easy Fit Poly fittings.

How tight should I tighten my Easy Fit MD compression fittings?

Hansen gives two lines of guidance. Its product page FAQ says: "Up to 32mm just tighten hand tight and all sizes above use a spanner to tighten another ½ to 1 turns past hand tight." Its installation sheet says: "Firmly hand tighten the Nut. Use a pair of Poly Grips for a further half turn past hand tight for final tightening on 40mm fittings and greater." Hansen adds that you already have a seal once the pipe is past the O-ring; the nut only compresses the grip ring to hold the pipe in place.

Do I need to chamfer the pipe?

Yes. Hansen's installation steps say to cut the pipe square, chamfer the end and clean off burrs. We stock the Hansen Chamfering Tool (HMDCHAMF).

Does this fitting carry Hansen's Limited Lifetime Warranty?

Yes. All Hansen manufactured products carry Hansen's Limited Lifetime Warranty (conditions apply). Hansen says installing outside the listed pipe installation standards may void its warranty.