Search

HAN-HMDRT4032

Hansen - MDPE Tee & Reducing - HMDT - HMDRT

Top of Tee - Both
Bottom of Tee

How to choose your size

  • Top of Tee - Both: the straight-through run. Both run ends are the same size.
  • Bottom of Tee: the branch.
  • Equal tee: pick the same size for both (e.g. 25 x 25). Reducing tee: pick the run as Top of Tee - Both and the smaller branch as Bottom of Tee (e.g. 25 x 20).

Combinations that aren't made are greyed out.

Big Water Tanks is an official stockist of Hansen Products — New Zealand-made pipe fittings for farm, irrigation, rural water and plumbing. The Hansen Easy Fit MD Compression Tee (HMDT) branches a medium density polyethylene (MDPE) pipe line with all three ends the same size, and the Reducing Tee Connector (HMDRT) has a smaller branch. 9 equal tees from 20mm to 110mm and 11 reducing tees from 25 x 25 x 20mm to 110 x 110 x 90mm.

Hansen Easy Fit MD Compression Tee (HMDT) & Reducing Tee (HMDRT): MDPE Pipe × MDPE Pipe × MDPE Pipe

A tee takes a branch off an MDPE pipe line. The top of the tee is the straight-through run, and both run ends are always the same size; the bottom of the tee is the branch. On the equal tee (HMDT) all three ends are the same size. On the reducing tee (HMDRT) the branch is smaller, for example a 32mm main with a 25mm branch. Hansen describes both as "used for connecting Medium Density Polyethylene Pipe (MDPE). Pipe Size x Pipe Size x Pipe Size." All three ends are compression ends: undo the nut to the last thread, push the pipe through the nut, white grip ring and thrust ring and past the seal to the stop, then tighten the nut. Hansen says the hydraulic seal is made when the pipe passes the seal; tightening the nut gives pull-out resistance. There are no threads, Poly Nuts or barbed tails, so these tees are for metric outside diameter MDPE pipe, not low density (LDPE) poly pipe. Hansen makes them in New Zealand from UV stabilised polypropylene, and the Easy Fit Compression range carries WaterMark certification and is tested to AS/NZS 4020:2018 for contact with drinking water.

Quick Facts

  • Connection: MDPE pipe × MDPE pipe × MDPE pipe, compression ends on all three (nut, grip ring, thrust ring, O-ring and seal). No threaded ends
  • Equal tees (HMDT): 20, 25, 32, 40, 50, 63, 75, 90 and 110mm, all three ends the same size
  • Reducing tees (HMDRT): 11 sizes from 25 x 25 x 20mm to 110 x 110 x 90mm. The first number is the run (top of the tee, both ends), the second is the branch
  • Fits: Medium density polyethylene pipe (PE80 and PE100) to AS/NZS 4130, sized by outside diameter
  • Max working pressure: 16 bar (1,600 kPa, 235 psi) for 20mm to 63mm; 12.5 bar (1,250 kPa, 182 psi) for 75mm to 110mm, at 20°C
  • Materials: Polypropylene body and nuts, acetal grip ring, polypropylene thrust ring, nitrile rubber O-ring and seal
  • Approvals: WaterMark WMKA21978 (AS/NZS 4129:2020), AS/NZS 4020:2018 drinking water, WRAS
  • Made in: New Zealand (Hansen Products, Whangarei)

Key Features & Benefits

  • Made in New Zealand: Manufactured using the best quality materials to withstand the harshest weather conditions
  • Largest MD Range Made in NZ: Hansen says it is the largest medium density fitting range made in New Zealand
  • One Piece Fitting: Captive components when the fitting is assembled correctly
  • Pre-lubricated Seal: For easy pipe insertion and reliable leak free connections
  • UV Stabilised: Weather, termite, fungi and bacterial resistance
  • High Pressure Rated: 16 bar up to 63mm, 12.5 bar from 75mm to 110mm
  • Sleek, Compact Design: For easy installation
  • Easy Grip Nuts: For rapid winding onto the pipe
  • Drinking Water Approved: Potable (drinkable) water approved
  • Hansen Limited Lifetime Warranty: All Hansen manufactured products carry Hansen's Limited Lifetime Warranty (conditions apply)
  • Trusted for Over 50 Years: Hansen has been making pipe fittings in New Zealand for over 50 years

Choosing Your MD Tee

Equal or reducing?

Use an equal tee (HMDT) when the branch is the same size as the line. Use a reducing tee (HMDRT) for a smaller branch: in the code, the first number is the run (both ends of the top of the tee) and the second is the branch. The HMDRT3225 has 32mm run ends and a 25mm branch (32 x 32 x 25mm).

How to order

Choose Top of Tee - Both (the run) and Bottom of Tee (the branch) above. Same size for both gives the equal tee; a smaller Bottom of Tee gives the reducing tee.

Measure the pipe

MDPE is sized by its outside diameter, so a 32mm tee suits pipe with a 32mm outside diameter. Check the pipe table below.

Need a different fitting?

Delivery or Collection

Stock Sizes up to 50mm are stocked in store. We hold limited stock of larger sizes, and can order them in if needed.
Delivery Courier nationwide. Shipping is calculated at checkout based on your location.
Collections Available from 21 Akatea Road, Glendene, Auckland.

Materials & Standards

Easy Fit Compression Fittings Materials

Part Material
Body & Nuts High quality polypropylene (virgin PP)
Grip Ring High quality acetal (virgin POM)
Thrust Ring High quality polypropylene (PP)
O-Ring High quality nitrile rubber (NBR)
Seal High quality nitrile rubber (NBR)

UV stabilised. Materials are from Hansen's Easy Fit Compression Fittings materials list.

WaterMark — AS/NZS 4129:2020

WaterMark Certificate of Conformity (Level 1), evaluated to AS/NZS 4129:2020 — Fittings for polyethylene (PE) pipes for pressure applications. Certificate No. WMKA21978, issued by SAI Global, current to 29 July 2028. Hansen's Easy Fit MD Compression range, including the HMDT tees and all HMDRT reducing tees, is covered by this certificate.

AS/NZS 4020:2018 — Products in Contact with Drinking Water

Hansen Easy Fit Compression Fittings (MD) were tested to AS/NZS 4020:2018 by the Australian Water Quality Centre (report 369234, completed 31 August 2023).

WRAS

WRAS product approval 240504011 for the Hansen Easy Fit range of polypropylene compression fittings, valid to May 2029.

Pressure Rating

Fitting Sizes Max @ 20°C kPa psi
20mm – 63mm 16 bar 1,600 kPa 235 psi
75mm – 110mm 12.5 bar 1,250 kPa 182 psi

Hansen's maximum working pressures at 20°C (68°F). Your pipe's own pressure class may be lower, so check the pipe table below.

Installation in Brief

Reliable leak-proof seals are the hallmark of Hansen fittings, and the Easy Fit Compression range installs in four simple steps:

Hansen Easy Fit MD compression install step 1: cutting MDPE pipe square with pipe cutters

1Cut and chamfer

Cut the pipe square with pipe cutters, a knife or saw, and chamfer the pipe end. Clean off any burrs and keep the pipe end clean and as free of scratches as possible.

Hansen Easy Fit MD compression install step 2: nut undone to the last thread

2Undo the nut

Undo the nut to the last thread. Don't remove the nut from the body.

Hansen Easy Fit MD compression install step 3: pipe pushed past the seal to the stop point, showing grip ring and thrust ring

3Push the pipe in

Push the pipe through the nut, white grip ring and thrust ring until it meets the seal, then push firmly past the seal all the way to the stop point.

Hansen Easy Fit MD compression install step 4: hand tightening the nut

4Tighten

Firmly hand tighten the nut. On 40mm and greater, use a pair of Poly Grips for a further half turn past hand tight.

Note: The hydraulic seal is made when the pipe passes the seal; tightening the nut gives pull-out resistance.

Hansen's product page FAQ also says: "Up to 32mm just tighten hand tight and all sizes above use a spanner to tighten another ½ to 1 turns past hand tight."

Chamfering the pipe end makes it easier to push past the seal. We stock the Hansen Chamfering Tool (HMDCHAMF).

Installation standards

Hansen says Easy Fit Compression fittings should be installed onto medium density pipe that has been installed in accordance with:

  • AS/NZS 2566 Part 1 and Supplement "Buried Flexible Pipelines — Structural Design" (detailed installation and site pressure testing)
  • AS/NZS 2566 Part 2 "Installation"
  • AS/NZS 2033 Installation of Polyethylene Pipe Systems

Not following these standards may void any warranties given by Hansen Products (NZ) Limited for the fitting. Follow the pipe manufacturer's guidelines.

Hansen's MD Compression Fitting Handy Tips: handy tips for installing Easy Fit Compression fittings on MDPE pipe.

Full Size Table — All 20 Hansen MD Tees & Reducing Tees

Hansen Code Run x Run x Branch Max @ 20°C Spare Parts
Equal Tees (HMDT)
HMDT20 20 x 20 x 20mm 16 bar 20mm spares
HMDT25 25 x 25 x 25mm 16 bar 25mm spares
HMDT32 32 x 32 x 32mm 16 bar 32mm spares
HMDT40 40 x 40 x 40mm 16 bar 40mm spares
HMDT50 50 x 50 x 50mm 16 bar 50mm spares
HMDT63 63 x 63 x 63mm 16 bar 63mm spares
HMDT75 75 x 75 x 75mm 12.5 bar 75mm spares
HMDT90 90 x 90 x 90mm 12.5 bar 90mm spares
HMDT110 110 x 110 x 110mm 12.5 bar 110mm spares
Reducing Tees (HMDRT)
HMDRT2520 25 x 25 x 20mm 16 bar 25mm spares & 20mm spares
HMDRT3220 32 x 32 x 20mm 16 bar 32mm spares & 20mm spares
HMDRT3225 32 x 32 x 25mm 16 bar 32mm spares & 25mm spares
HMDRT4032 40 x 40 x 32mm 16 bar 40mm spares & 32mm spares
HMDRT5032 50 x 50 x 32mm 16 bar 50mm spares & 32mm spares
HMDRT5040 50 x 50 x 40mm 16 bar 50mm spares & 40mm spares
HMDRT6350 63 x 63 x 50mm 16 bar 63mm spares & 50mm spares
HMDRT7563 75 x 75 x 63mm 12.5 bar 75mm spares & 63mm spares
HMDRT9075 90 x 90 x 75mm 12.5 bar 90mm spares & 75mm spares
HMDRT11063 110 x 110 x 63mm 12.5 bar 110mm spares & 63mm spares
HMDRT11090 110 x 110 x 90mm 12.5 bar 110mm spares & 90mm spares

Codes and sizes are from Hansen's catalogue; pressures are Hansen's at 20°C. The Spare Parts column links to the matching size of our Hansen Compression Spare Parts; choose the thrust ring, nut, grip ring or O-ring there. Hansen lists four spare parts for each pipe end size: thrust ring, grip ring, nut and O-ring. Reducing tees use spares in both sizes: the run size for the two top ends and the branch size for the bottom. Big Water Tanks sells all the spare parts. To order, pick Top of Tee - Both (the run) and Bottom of Tee (the branch) above: 25mm / 25mm = HMDT25; 25mm / 20mm = HMDRT2520.

Pipe the HMDT & HMDRT Fit — PE Pipe to AS/NZS 4130:2018

Hansen's Easy Fit Compression pipe specification: AS/NZS 4130:2018 polyethylene pipes for pressure applications. Mean outside diameter and wall thickness (min–max) in mm, by pressure class.

Nominal OD Mean OD PN6.3 Wall PN9 Wall PN12.5 Wall PN16 Wall
20 20.0–20.3 1.6–1.9* 1.6–1.9* 1.9–2.2 1.9–2.2
25 25.0–25.3 1.6–1.9* 1.6–1.9* 2.3–2.7 2.3–2.7
32 32.0–32.3 1.6–1.9 1.9–2.2* 2.9–3.3 2.9–3.3
40 40.0–40.4 1.9–2.2 2.4–2.8* 3.7–4.2 3.7–4.2
50 50.0–50.5 2.4–2.8 3.0–3.4* 4.6–5.2 4.6–5.2
63 63.0–63.6 3.0–3.4 3.8–4.3* 5.8–6.5 5.8–6.5
75 75.0–75.7 3.6–4.1 4.5–5.1* 6.8–7.6 6.8–7.6
90 90.0–90.9 4.3–4.9 5.4–6.1* 8.2–9.2 8.2–9.2
110 110.0–111.0 5.3–6.0 6.6–7.4* 10.0–11.1 10.0–11.1

PN6.3, PN9 and PN12.5 are PE80; PN16 is PE100. Pipe working pressures: PN6.3 0.63 MPa (91.4 psi), PN9 0.90 MPa (130.5 psi), PN12.5 1.25 MPa (181.3 psi), PN16 1.60 MPa (232.1 psi). *Hansen notes these wall thicknesses are not included in AS/NZS 4130:2018 and are based on industry documentation.

Chemical Compatibility

Using your tees with anything other than water? Hansen's Easy Fit Compression chemical resistance chart rates the polypropylene, acetal and nitrile rubber parts separately. Check it before you install.

View MD Compression Chemical Chart

Installation Guide

Hansen's Easy Fit MD Compression cheat sheet covers cutting, chamfering, inserting the pipe and tightening, with the installation standards to follow.

Download MD Installation Sheet (PDF)

Frequently Asked Questions

What is a Hansen MD tee used for?

Hansen says the HMDT and HMDRT are used for connecting medium density polyethylene pipe (MDPE), pipe size x pipe size x pipe size. A tee takes a branch off a line. The HMDT has all three ends the same size; the HMDRT has a smaller branch.

Which end is the top and which is the bottom?

The top of the tee is the straight-through run: its two ends are always the same size. The bottom of the tee is the branch. Pick Top of Tee - Both for your main line size and Bottom of Tee for the branch size.

How do I read the HMDRT code?

The first number is the run (both top ends) and the second is the branch. The HMDRT5032 has 50mm run ends and a 32mm branch (50 x 50 x 32mm).

Does the tee have a threaded end?

No. All three ends are compression ends for MDPE pipe. For a threaded branch, use the MD Male Threaded Tee (HMDMT) or MD Female Threaded Tee (HMDFT).

Will these fit my low density (LDPE) poly pipe?

No. Hansen designs its Easy Fit Compression fittings for medium density polyethylene pipe, sized by outside diameter. For low density poly pipe use Hansen Easy Fit Poly fittings, such as the Easy Fit Poly Tee & Reducing Tee (HT / HRT).

How tight should I tighten my Easy Fit MD compression fittings?

Hansen gives two lines of guidance. Its product page FAQ says: "Up to 32mm just tighten hand tight and all sizes above use a spanner to tighten another ½ to 1 turns past hand tight." Its installation sheet says: "Firmly hand tighten the Nut. Use a pair of Poly Grips for a further half turn past hand tight for final tightening on 40mm fittings and greater." Hansen adds that you already have a seal once the pipe is past the O-ring; the nut only compresses the grip ring to hold the pipe in place.

Do I need to chamfer the pipe?

Yes. Hansen's installation steps say to cut the pipe square, chamfer the end and clean off burrs. We stock the Hansen Chamfering Tool (HMDCHAMF).

Can I use MD fittings in my house water supply?

Yes. Hansen says its Easy Fit MD Compression fittings are potable (drinking) water approved. They have been tested to AS/NZS 4020:2018 (AWQC report 369234) and carry WaterMark certification WMKA21978.

What pressure are they rated to?

Hansen rates 20mm to 63mm at 16 bar (1,600 kPa, 235 psi) and 75mm to 110mm at 12.5 bar (1,250 kPa, 182 psi), at 20°C. Your pipe's pressure class may be lower.

Can I get spare parts?

Yes. Hansen lists a thrust ring, grip ring, nut and O-ring for each size, and Big Water Tanks sells all the spare parts: order them from our Hansen Compression Spare Parts page by part and size. A reducing tee uses spares in both sizes: the run size for the two top ends and the branch size for the bottom.

Can I use Hansen Easy Fit fittings under driveways, paths and foundations?

No. Hansen does not recommend the use of any Hansen Easy Fit fittings under any driveways, paths or foundations.

Does this fitting carry Hansen's Limited Lifetime Warranty?

Yes. All Hansen manufactured products carry Hansen's Limited Lifetime Warranty (conditions apply). Hansen says installing outside the listed pipe installation standards may void its warranty.

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
M
Martin Thompson
Great service

Again great service